Impact of the photo-induced degradation of electron acceptors on the photophysics, charge transport and device performance of all-polymer and fullerene–polymer solar cells

The photodegeneration of polymer solar cells (PSCs) based on polymer donors and fullerene acceptors limits their lifetime and reliability. Here, we demonstrate that replacing fullerene acceptors with naphthalenediimide (NDI)-based n-type polymers can significantly enhance the photo-stability of PSCs. As a model system, we compared the photo-stabilities of all-polymer solar cells (all-PSCs) and fullerene-based PSCs (fullerene-PSCs) using the same polymer donor (PBDTTTPD) exposed to one sunlight illumination. We observed a remarkable contrast in their photo-stabilities. After 4 days of irradiation, the performance of the fullerene-PSCs dropped by 50%, whereas the performance of the all-PSCs remained stable. The detailed analysis of charge dynamics measured by femtosecond transient absorption spectroscopy and space charge limited current measurements shows significant reduction in interfacial charge transfer and charge carrier mobility, which correlates with the loss in JSC and FF of the fullerene-PSCs under solar illumination. By contrast, for the all-PSCs, the ultrafast dynamics and charge mobility remained consistent after illumination. The NDI-based copolymer had high stability under light exposure, whereas the photo-induced dimerization of phenyl-C61-butyric acid methyl ester (PCBM) acceptors was responsible for the photo-degradation of fullerene-PSCs.

[1]  Nathan T. Shewmon,et al.  Photodegradation of Metal Oxide Interlayers in Polymer Solar Cells , 2016 .

[2]  Yongfang Li,et al.  High-performance polymer solar cells based on a 2D-conjugated polymer with an alkylthio side-chain , 2016 .

[3]  He Yan,et al.  Aggregation and morphology control enables multiple cases of high-efficiency polymer solar cells , 2014, Nature Communications.

[4]  Timothy M. Burke,et al.  Disorder‐Induced Open‐Circuit Voltage Losses in Organic Solar Cells During Photoinduced Burn‐In , 2015 .

[5]  Cheng Wang,et al.  Flexible, highly efficient all-polymer solar cells , 2015, Nature Communications.

[6]  Yang Yang,et al.  Low-Bandgap Near-IR Conjugated Polymers/Molecules for Organic Electronics. , 2015, Chemical reviews.

[7]  Bumjoon J. Kim,et al.  Charge Generation Dynamics in Efficient All-Polymer Solar Cells: Influence of Polymer Packing and Morphology. , 2015, ACS applied materials & interfaces.

[8]  Youyong Li,et al.  Efficient Polymer Solar Cells with a High Open Circuit Voltage of 1 Volt , 2013 .

[9]  Feng Liu,et al.  Single-junction polymer solar cells with high efficiency and photovoltage , 2015, Nature Photonics.

[10]  Jenny Clark,et al.  Ultrafast Long-Range Charge Separation in Organic Semiconductor Photovoltaic Diodes , 2014, Science.

[11]  Jun Liu,et al.  Polymer Acceptor Based on Double B←N Bridged Bipyridine (BNBP) Unit for High‐Efficiency All‐Polymer Solar Cells , 2016, Advanced materials.

[12]  J. Hummelen,et al.  Photodimerization of a m-phenylenebis(arylmethanofullerene): The first rigorous proof for photochemical inter-fullerene [2+2] cycloaddition , 2000 .

[13]  Ying Wang,et al.  Photoinduced Polymerization of Solid C60 Films , 1993, Science.

[14]  Daisuke Mori,et al.  Highly efficient charge-carrier generation and collection in polymer/polymer blend solar cells with a power conversion efficiency of 5.7% , 2014 .

[15]  Bumjoon J. Kim,et al.  High‐Performance All‐Polymer Solar Cells Via Side‐Chain Engineering of the Polymer Acceptor: The Importance of the Polymer Packing Structure and the Nanoscale Blend Morphology , 2015, Advanced materials.

[16]  S. Forrest,et al.  Photochemical origins of burn-in degradation in small molecular weight organic photovoltaic cells , 2015 .

[17]  T. Ngo,et al.  Glass transition of PCBM, P3HT and their blends in quenched state , 2012 .

[18]  Bumjoon J. Kim,et al.  Design of terpolymers as electron donors for highly efficient polymer solar cells , 2014 .

[19]  A. Tournebize,et al.  The effect of polymer solubilizing side-chains on solar cell stability. , 2015, Physical chemistry chemical physics : PCCP.

[20]  Tracey M. Clarke,et al.  Photodegradation in Encapsulated Silole‐Based Polymer: PCBM Solar Cells Investigated using Transient Absorption Spectroscopy and Charge Extraction Measurements , 2013 .

[21]  He Yan,et al.  Improved Performance of All‐Polymer Solar Cells Enabled by Naphthodiperylenetetraimide‐Based Polymer Acceptor , 2017, Advanced materials.

[22]  Jun Liu,et al.  Polymer Acceptor Based on B←N Units with Enhanced Electron Mobility for Efficient All-Polymer Solar Cells. , 2016, Angewandte Chemie.

[23]  Bertrand J. Tremolet de Villers,et al.  Removal of Residual Diiodooctane Improves Photostability of High-Performance Organic Solar Cell Polymers , 2016 .

[24]  P. Blom,et al.  Trap-assisted recombination in disordered organic semiconductors. , 2011, Physical review letters.

[25]  Gang Li,et al.  25th Anniversary Article: A Decade of Organic/Polymeric Photovoltaic Research , 2013, Advanced materials.

[26]  F. Liu,et al.  A Novel Naphtho[1,2‐c:5,6‐c′]Bis([1,2,5]Thiadiazole)‐Based Narrow‐Bandgap π‐Conjugated Polymer with Power Conversion Efficiency Over 10% , 2016, Advanced materials.

[27]  C. Brabec,et al.  Charge Transport and Recombination in Low‐Bandgap Bulk Heterojunction Solar Cell using Bis‐adduct Fullerene , 2011 .

[28]  Yongfang Li,et al.  Effects of Fullerene Bisadduct Regioisomers on Photovoltaic Performance , 2014 .

[29]  Eric T. Hoke,et al.  Ring Substituents Mediate the Morphology of PBDTTPD-PCBM Bulk-Heterojunction Solar Cells , 2014 .

[30]  Chain‐Shu Hsu,et al.  Donor-acceptor conjugated polymers based on multifused ladder-type arenes for organic solar cells. , 2015, Chemical Society reviews.

[31]  C. A. Walsh,et al.  Efficient photodiodes from interpenetrating polymer networks , 1995, Nature.

[32]  Zhe Li,et al.  Enhancing Fullerene-Based Solar Cell Lifetimes by Addition of a Fullerene Dumbbell** , 2014, Angewandte Chemie.

[33]  Jia Wang,et al.  Photochemical Transformation of Fullerenes , 2013 .

[34]  O. Inganäs,et al.  Low Band Gap Polymer Solar Cells With Minimal Voltage Losses , 2016 .

[35]  Antonio Facchetti,et al.  Polymer donor–polymer acceptor (all-polymer) solar cells , 2013 .

[36]  Zhenggang Huang,et al.  Performance enhancement of fullerene-based solar cells by light processing , 2013, Nature Communications.

[37]  Milos Nesladek,et al.  Influence of fullerene photodimerization on the PCBM crystallization in polymer: Fullerene bulk heterojunctions under thermal stress , 2013 .

[38]  T. Park,et al.  Morphological Control of Donor/Acceptor Interfaces in All-Polymer Solar Cells Using a Pentafluorobenzene-Based Additive , 2017 .

[39]  Bumjoon J. Kim,et al.  From Fullerene-Polymer to All-Polymer Solar Cells: The Importance of Molecular Packing, Orientation, and Morphology Control. , 2016, Accounts of chemical research.

[40]  J. Durrant,et al.  Photochemical stability of high efficiency PTB7:PC70BM solar cell blends , 2014 .

[41]  Kwanghee Lee,et al.  Air‐Stable Organic Solar Cells Using an Iodine‐Free Solvent Additive , 2016 .

[42]  Xiong Gong,et al.  Low bandgap semiconducting polymers for polymeric photovoltaics. , 2016, Chemical Society reviews.

[43]  S. Jenekhe,et al.  All‐Polymer Bulk Heterojuction Solar Cells with 4.8% Efficiency Achieved by Solution Processing from a Co‐Solvent , 2014, Advanced materials.

[44]  Akshay Rao,et al.  Exciton fission and charge generation via triplet excitons in pentacene/C60 bilayers. , 2010, Journal of the American Chemical Society.

[45]  Vishal Shrotriya,et al.  Organic photovoltaics: Polymer power , 2009 .

[46]  Bumjoon J. Kim,et al.  Determining the role of polymer molecular weight for high-performance all-polymer solar cells: its effect on polymer aggregation and phase separation. , 2015, Journal of the American Chemical Society.

[47]  Xiaojing Long,et al.  An Electron-Deficient Building Block Based on the B←N Unit: An Electron Acceptor for All-Polymer Solar Cells. , 2016, Angewandte Chemie.

[48]  Bumjoon J. Kim,et al.  Importance of Optimal Composition in Random Terpolymer-Based Polymer Solar Cells , 2013 .

[49]  Bumjoon J. Kim,et al.  Controlling Energy Levels and Blend Morphology for All-Polymer Solar Cells via Fluorination of a Naphthalene Diimide-Based Copolymer Acceptor , 2016 .

[50]  C. McNeill,et al.  Surface and Bulk Structural Characterization of a High-Mobility Electron-Transporting Polymer , 2011 .

[51]  Efficient light trapping in inverted polymer solar cells by a randomly nanostructured electrode using monodispersed polymer nanoparticles. , 2013, Nanoscale.

[52]  O. Inganäs,et al.  High Performance All-Polymer Solar Cells by Synergistic Effects of Fine-Tuned Crystallinity and Solvent Annealing. , 2016, Journal of the American Chemical Society.

[53]  J. Fréchet,et al.  Polymer-fullerene composite solar cells. , 2008, Angewandte Chemie.

[54]  Jianqi Zhang,et al.  All‐Polymer Solar Cells Based on Absorption‐Complementary Polymer Donor and Acceptor with High Power Conversion Efficiency of 8.27% , 2016, Advanced materials.

[55]  Jean Manca,et al.  Eco-friendly fabrication of PBDTTPD:PC71BM solar cells reaching a PCE of 3.8% using water-based nanoparticle dispersions , 2017 .

[56]  Fei Huang,et al.  Optimisation of processing solvent and molecular weight for the production of green-solvent-processed all-polymer solar cells with a power conversion efficiency over 9% , 2017 .

[57]  Hans-Joachim Egelhaaf,et al.  The Effect of PCBM Dimerization on the Performance of Bulk Heterojunction Solar Cells , 2014 .

[58]  Bryon W. Larson,et al.  Beyond PCBM: Understanding the Photovoltaic Performance of Blends of Indene‐C60 Multiadducts with Poly(3‐hexylthiophene) , 2012 .

[59]  H. Ade,et al.  A Vinylene‐Bridged Perylenediimide‐Based Polymeric Acceptor Enabling Efficient All‐Polymer Solar Cells Processed under Ambient Conditions , 2016, Advanced materials.

[60]  Bumjoon J. Kim,et al.  Photoinduced charge transfer in donor-acceptor (DA) copolymer: fullerene bis-adduct polymer solar cells. , 2013, ACS applied materials & interfaces.

[61]  Bumjoon J. Kim,et al.  Controlling Molecular Orientation of Naphthalenediimide‐Based Polymer Acceptors for High Performance All‐Polymer Solar Cells , 2016 .

[62]  F. Castro,et al.  Photochemical Transformations in Fullerene and Molybdenum Oxide Affect the Stability of Bilayer Organic Solar Cells , 2015 .

[63]  Bumjoon J. Kim,et al.  Effects of Solubilizing Group Modification in Fullerene Bis-Adducts on Normal and Inverted Type Polymer Solar Cells , 2012 .

[64]  Li-ping Zhu,et al.  High‐Performance Polymer Solar Cells with PCE of 10.42% via Al‐Doped ZnO Cathode Interlayer , 2016, Advanced materials.

[65]  Samson A Jenekhe,et al.  7.7% Efficient All‐Polymer Solar Cells , 2015, Advanced materials.

[66]  Garry Rumbles,et al.  Photoinduced Degradation of Polymer and Polymer–Fullerene Active Layers: Experiment and Theory , 2010 .

[67]  Yongfang Li,et al.  A Synergetic Effect of Molecular Weight and Fluorine in All‐Polymer Solar Cells with Enhanced Performance , 2017 .

[68]  John R. Tumbleston,et al.  The Importance of Fullerene Percolation in the Mixed Regions of Polymer–Fullerene Bulk Heterojunction Solar Cells , 2013 .

[69]  Samson A Jenekhe,et al.  All-polymer solar cells with 3.3% efficiency based on naphthalene diimide-selenophene copolymer acceptor. , 2013, Journal of the American Chemical Society.

[70]  D. Bradley,et al.  Influence of the Hole Transporting Layer on the Thermal Stability of Inverted Organic Photovoltaics Using Accelerated-Heat Lifetime Protocols , 2017, ACS applied materials & interfaces.

[71]  Zhaojun Li,et al.  High‐Performance and Stable All‐Polymer Solar Cells Using Donor and Acceptor Polymers with Complementary Absorption , 2017 .

[72]  S. Forrest,et al.  Photodegradation of small-molecule organic photovoltaics , 2014 .

[73]  Jin Jang,et al.  A high efficiency solution processed polymer inverted triple-junction solar cell exhibiting a power conversion efficiency of 11.83% , 2015 .

[74]  T. Wågberg,et al.  Photo-induced and resist-free imprint patterning of fullerene materials for use in functional electronics. , 2009, Journal of the American Chemical Society.

[75]  A. M. Rao,et al.  Photochemical transformation of C60 and C70 films , 1995 .

[76]  Bumjoon J. Kim,et al.  Comparative Study of Thermal Stability, Morphology, and Performance of All-Polymer, Fullerene–Polymer, and Ternary Blend Solar Cells Based on the Same Polymer Donor , 2017 .

[77]  C. Brabec,et al.  Morphological and electrical control of fullerene dimerization determines organic photovoltaic stability , 2016 .

[78]  A. S. Dudnik,et al.  All-Polymer Solar Cell Performance Optimized via Systematic Molecular Weight Tuning of Both Donor and Acceptor Polymers. , 2016, Journal of the American Chemical Society.

[79]  Alberto Salleo,et al.  High Performance All‐Polymer Solar Cell via Polymer Side‐Chain Engineering , 2014, Advanced materials.