Influence of surface morphology on corrosion and electronic behavior

Electrochemical or mechanochemical behavior of a surface, such as corrosion or corrosive wear, is extremely complicated and involves various chemical, physical and mechanical factors. To gain a thorough insight into such a complex phenomenon, it is necessary to understand the role of each factor. In this study, the influence of surface morphology, represented by roughness, on the corrosion and electronic behavior, represented by the electron work function (EWF), of copper was investigated using an atomic force microscope and a scanning Kelvin probe. Experimental results showed that the corrosion rate increased with an increase in surface roughness, whereas its surface EWF decreased. It was theoretically demonstrated that roughness can decrease the average EWF but increase the fluctuation of the local EWF. Such fluctuation could promote the formation of microelectrodes and, therefore, accelerate corrosion. The study demonstrates that the surface morphology can make a considerable contribution to corrosion and thus corrosive wear.

[1]  David A. Rigney,et al.  Application of the contact potential difference technique for on-line rubbing surface monitoring (review) , 1998 .

[2]  A. L. Ortiz,et al.  Wear-resistant ultra-fine-grained ceramics , 2005 .

[3]  W. Li,et al.  Effect of surface geometrical configurations induced by microcracks on the electron work function , 2005 .

[4]  W. Li,et al.  On the correlation between surface roughness and work function in copper. , 2005, The Journal of chemical physics.

[5]  W. Li,et al.  Effects of dislocation on electron work function of metal surface , 2002 .

[6]  G. Burstein,et al.  The generation of surface roughness during slurry erosion-corrosion and its effect on the pitting potential , 1996 .

[7]  Dongyang Li,et al.  A study on the kinetic response of the electron work function to wear , 2003 .

[8]  R. Imbihl,et al.  Spiral waves and formation of low work function areas in catalytic NO reduction with hydrogen on a Rh(111) surface , 2002 .

[9]  W. R. Salaneck,et al.  Characterisation of the properties of surface-treated indium-tin oxide thin films , 1999 .

[10]  G. Frankel,et al.  Characterization of Corrosion Interfaces by the Scanning Kelvin Probe Force Microscopy Technique , 2001 .

[11]  M. Stratmann,et al.  The structure and stability of metal surfaces modified by silane Langmuir-Blodgett films , 1992 .

[12]  Weiwei Li,et al.  Electron work function: A parameter sensitive to the adhesion behavior of crystallographic surfaces , 2001 .

[13]  Junji Itoh,et al.  Field emission from flat metal surfaces covered with Ba atoms , 1999 .

[14]  D. Li,et al.  Effects of elastic and plastic deformations on the electron work function of metals during bending tests , 2004 .

[15]  T. Tani,et al.  Effects of surface roughness and patches on the work function of cobalt , 1994 .

[16]  Rui F. Silva,et al.  MODELING OF CHEMICAL WEAR IN FERROUS ALLOYS/ SILICON NITRIDE CONTACTS DURING HIGH SPEED CUTTING , 1998 .

[17]  Michael D. Fayer,et al.  Elements Of Quantum Mechanics , 2001 .

[18]  D. Li,et al.  Determination of the yield locus using a Kelvin probing method , 2004 .

[19]  Peter J. Smith,et al.  Multitip scanning bio-Kelvin probe , 1999 .

[20]  D. Thierry,et al.  Investigation of Filiform Corrosion on Coated Aluminum Alloys by FTIR Microspectroscopy and Scanning Kelvin Probe , 2002 .

[21]  J. Dumbleton,et al.  The unlubricated adhesive wear resistance of metastable austenitic stainless steels containing silicon , 1977 .

[22]  D. Rigney,et al.  Friction, wear and microstructure of unlubricated austenitic stainless steels☆ , 1980 .

[23]  Weiwei Li,et al.  Variations of work function and corrosion behaviors of deformed copper surfaces , 2005 .

[24]  J. Llorca,et al.  Modeling the effect of temperature on the wear resistance of metals reinforced with ceramic particles , 2000 .

[25]  D. Thierry,et al.  Scanning Kelvin probe study of metal/polymer interfaces , 2004 .

[26]  N. Zettili.  Quantum Mechanics: Concepts and Applications , 2001 .

[27]  T. Magnin,et al.  The corrosion-enhanced plasticity model for stress corrosion cracking in ductile fcc alloys , 1996 .

[28]  J. Svensson,et al.  Scanning Kelvin Probe Force Microscopy A Useful Tool for Studying Atmospheric Corrosion of MgAl Alloys In Situ , 2003 .

[29]  A. Sehgal,et al.  Synergistic effects of chromium depletion and ohmic potential drop on the susceptibility to intergranular corrosion and hydrogen embrittlement of sensitized stainless steel , 1997 .

[30]  S. B. Axelsen,et al.  Simultaneous In Situ Infrared Reflection Absorption Spectroscopy and Kelvin Probe Measurements during Atmospheric Corrosion , 2001 .

[31]  Dongyang Li,et al.  The effect of YCl3 and LaCl3 additives on wear of 1045 and 304 steels in a dilute chloride solution , 2003 .

[32]  X. Wang,et al.  Investigation of the Synergism of Wear and Corrosion Using an Electrochemical Scratch Technique , 2001 .