Numerical analysis of a GPHE’s hydrodynamic and thermal characteristics, by applying an iterative procedure for the thermal boundary conditions

Abstract The current study presents a new methodology for Gasketed Plate Heat Exchanger (GPHE) efficiency prediction using as a basis a Computational Fluid Dynamics (CFD) model, detailed enough to reproduce the complicated characteristics of the induced flow patterns exhibited in a single flow channel characterized by difficult geometrical patterns. Compared to other similar approaches an iterative procedure for the imposition of the most appropriate thermal boundary conditions is proposed. For the presentation of this methodology and its validation against available design data, a model of an existing GPHE consisting of 24 plates (thus 23 channels) was tested. At first a mesh independence study was performed, while with the selected grid density a deviation of around 15% of numerical predictions for the calculated overall pressure drop compared to the design values was tracked. This level of discrepancy can be attributed to the uncertainty of channel spacing, which influences significantly the pressure losses and for which unfortunately no concrete measurements can be made, owed to no actual access to the plate manufacturing process itself. With the use of the CFD model, the strong dependency between pressure drop and plate distance was quantified, as for an increment of 1.88% of the plate pack length, a 39% decrease in pressure drop was calculated. This highpoints the importance of plate tightening process, after its manufacturing, as a crucial specification parameter during the design of such type of heat exchangers; highlighting at the same time how the proposed CFD tool can act as an important supporting tool in the design of such type of complicated Heat Exchangers. Following the prediction of pressure drop, a new proposed boundary conditions imposition approach was applied in the model, making it possible to estimate the whole GPHE heat transfer efficiency with a 6% error compared to the design values The developed and validated methodology can facilitate especially the design of large scale GPHE, since long-term testing campaigns for the optimization of such components, especially in industrial applications, are highly costly.

[1]  Spiros V. Paras,et al.  4 th International Conference on Heat Transfer, Fluid Mechanics, and Thermodynamics Cairo, Egypt Paper number: KA2 NUMERICAL AND EXPERIMENTAL INVESTIGATION OF FLOW AND HEAT TRANSFER IN NARROW CHANNELS WITH CORRUGATED WALLS , 2005 .

[2]  HFC32 vaporisation inside a Brazed Plate Heat Exchanger (BPHE): Experimental measurements and IR thermography analysis , 2015 .

[3]  Stéphane Launay,et al.  Complex 3D-flow analysis and corrugation angle effect in plate heat exchangers , 2015 .

[4]  Nur Rohmah,et al.  The Effect of Plate Spacing in Plate Heat Exchanger Design as a Condenser in Organic Rankine cycle for Low Temperature Heat Source , 2015 .

[5]  Félix Barreras,et al.  The flow in an oil/water plate heat exchanger for the automotive industry , 2008 .

[6]  Y. Tsai,et al.  Investigations of the pressure drop and flow distribution in a chevron-type plate heat exchanger , 2009 .

[7]  Guangming Chen,et al.  A numerical and experimental study of chevron, corrugated-plate heat exchangers , 2010 .

[8]  Andreas Schuster,et al.  Influence of supercritical ORC parameters on plate heat exchanger design , 2012 .

[9]  W. Focke,et al.  The effect of the corrugation inclination angle on the thermohydraulic performance of plate heat exchangers , 1985 .

[10]  Damir Dović,et al.  Influence of chevron plates geometry on performances of plate heat exchangers , 2007 .

[11]  S. Paras,et al.  Optimal design of a plate heat exchanger with undulated surfaces , 2009 .

[12]  Numerical Analysis of Plate Heat Exchanger Performance in Co-Current Fluid Flow Configuration , 2009 .

[13]  V. Gullapalli,et al.  CFD Simulation of Heat Transfer and Pressure Drop in Compact Brazed Plate Heat Exchangers , 2014 .

[14]  Petro O. Kapustenko,et al.  The influence of plate corrugations geometry on plate heat exchanger performance in specified process conditions , 2013 .

[15]  Kwan-Soo Lee,et al.  Flow characteristics and thermal performance in chevron type plate heat exchangers , 2014 .

[16]  Guan-min Zhang,et al.  Simulation and Analysis of Flow Pattern in Cross-Corrugated Plate Heat Exchangers , 2006 .

[17]  Ji Hwan Jeong,et al.  Development of a numerical analysis model using a flow network for a plate heat exchanger with consideration of the flow distribution , 2017 .

[18]  T. Pääkkönen,et al.  EVALUATION OF HEAT TRANSFER BOUNDARY CONDITIONS FOR CFD MODELING OF A 3D PLATE HEAT EXCHANGER GEOMETRY , 2007 .

[19]  L. Tadrist,et al.  Local vs global heat transfer and flow analysis of hydrocarbon complete condensation in plate heat exchanger based on infrared thermography , 2015 .

[20]  S. Kabelac,et al.  Investigation of local heat transfer coefficients in plate heat exchangers with temperature oscillation IR thermography and CFD , 2010 .

[21]  Kwan-Soo Lee,et al.  Friction and Colburn factor correlations and shape optimization of chevron-type plate heat exchangers , 2015 .

[22]  C. T. Nguyen,et al.  Effects of smooth longitudinal passages and port configuration on the flow and thermal fields in a plate heat exchanger , 2011 .

[23]  Spiros V. Paras,et al.  Flow and Heat Transfer in Narrow Channels with Corrugated Walls: A CFD Code Application , 2005 .