The effect of temperature on the nanoscale adhesion and friction behaviors of thermoplastic polymer films

Adhesion and friction tests were carried out in order to investigate the effect of temperature on the tribological characteristics of poly(methylmethacrylate) (PMMA) film using AFM. The pull-off and friction forces on the PMMA film were measured under a high vacuum condition (below 1 × 10(-4) Pa) as the temperature of the PMMA film was increased from 300 to 420 K (heating) and decreased to 300 K (cooling). Friction tests were also conducted in both high vacuum and air conditions at room temperature. When the temperature was 420 K, which is 25 K higher than the glass-transition temperature (T(g)) of PMMA, the PMMA film surface became deformable. Subsequently, the pull-off force increased in proportion to the maximum applied load during the pull-off force measurement. In contrast, when the temperature was under 395 K, the pull-off force did not depend on the maximum applied load. The friction force began to increase when the temperature rose above 370 K, which is 25 K lower than the T(g) of PMMA, and rapidly increased at 420 K. Decrease of the PMMA film stiffness and plastic deformation of the PMMA film were observed at 420 K in force-displacement curves. After the heating to 420 K, the coefficient of friction was measured under air condition at room temperature and was found to be lower than that measured before the heating. Additionally, the RMS roughness increased as a result of heating.

[1]  Bharat Bhushan,et al.  Microfabrication and nanomechanical characterization of polymer microelectromechanical system for biological applications , 2005 .

[2]  P. Couturier.  Japan , 1988, The Lancet.

[3]  S. H. Kim,et al.  Fabrication of a 50 nm half-pitch wire grid polarizer using nanoimprint lithography , 2005 .

[4]  S. Chou,et al.  Nanoimprint Lithography , 2010 .

[5]  Dynamics of alpha and beta processes in thin polymer films: poly(vinyl acetate) and poly(methyl methacrylate). , 2001, Physical review. E, Statistical, nonlinear, and soft matter physics.

[6]  J. Seekamp,et al.  Fabrication of semiconductor-and polymer-based photonic crystals using nanoimprint lithography , 2005 .

[7]  Jean-Pierre Petit,et al.  Stress drop and contact stiffness measured from stick-slip experiments on PMMA-PMMA friction , 1999 .

[8]  Durability studies of micro/nanoelectromechanical systems materials, coatings and lubricants at high sliding velocities (up to 10mm∕s) using a modified atomic force microscope , 2005 .

[9]  J. Sader,et al.  Calibration of rectangular atomic force microscope cantilevers , 1999 .

[10]  L. Guo,et al.  High-resolution organic polymer light-emitting pixels fabricated by imprinting technique , 2002 .

[11]  Eui-Sung Yoon,et al.  Tribological properties of bio-mimetic nano-patterned polymeric surfaces on silicon wafer , 2006 .

[12]  Helmut Schift,et al.  Flow behaviour of thin polymer films used for hot embossing lithography , 2000 .

[13]  B. Dong,et al.  A study on carbon nanotubes reinforced poly(methyl methacrylate) nanocomposites , 2005 .

[14]  F.-C. Hong,et al.  Fabrication of large-scaled organic light emitting devices on the flexible substrates using low-pressure imprinting lithography , 2005, IEEE Transactions on Electron Devices.

[15]  Bharat Bhushan,et al.  Scale dependence of micro/nano-friction and adhesion of MEMS/NEMS materials, coatings and lubricants , 2004 .

[16]  Chung-Yen Chao,et al.  Polymer microring resonators fabricated by nanoimprint technique , 2002 .

[17]  Izhak Etsion,et al.  An improved wedge calibration method for lateral force in atomic force microscopy , 2003 .

[18]  Kwang-Seop Kim,et al.  Molecular dynamics study of pattern transfer in nanoimprint lithography , 2007 .

[19]  Bharat Bhushan,et al.  Hydrophobicity, adhesion, and friction properties of nanopatterned polymers and scale dependence for micro- and nanoelectromechanical systems. , 2005, Nano letters.

[20]  Y. Hirai,et al.  High Aspect Pattern Fabrication by Nano Imprint Lithography Using Fine Diamond Mold , 2002, 2002 International Microprocesses and Nanotechnology Conference, 2002. Digest of Papers..

[21]  Xudong Xiao,et al.  Studying Surface Glass-to-Rubber Transition Using Atomic Force Microscopic Adhesion Measurements , 2000 .

[22]  Wei Zhang,et al.  Fabrication of 60-nm transistors on 4-in. wafer using nanoimprint at all lithography levels , 2003 .

[23]  J. R. Smith,et al.  Friction coefficient mapping using the atomic force microscope , 2004 .

[24]  George M. Whitesides,et al.  UNCONVENTIONAL NANOFABRICATION , 2004 .

[25]  Stephen Y. Chou,et al.  Imprint of sub-25 nm vias and trenches in polymers , 1995 .

[26]  Graham Williams,et al.  Anelastic and Dielectric Effects in Polymeric Solids , 1991 .

[27]  A. V. Pocius,et al.  Adhesion and Adhesives Technology: An Introduction , 1996 .

[28]  Bharat Bhushan,et al.  Micro/nanotribological characterization of PDMS and PMMA used for BioMEMS/NEMS applications , 2005 .

[29]  J. Schultz,et al.  Study of solution-cast films of PMMA by dielectric spectroscopy: Influence of the nature of the solvent on α and β relaxations , 1997 .

[30]  Naoki Ono,et al.  Measurement of Young's Modulus of Silicon Single Crystal at High Temperature and Its Dependency on Boron Concentration Using the Flexural Vibration Method , 2000 .

[31]  Greg Haugstad,et al.  Probing Polymer Viscoelastic Relaxations with Temperature-Controlled Friction Force Microscopy , 1998 .

[32]  Wei Wu,et al.  Fabrication of 5 nm linewidth and 14 nm pitch features by nanoimprint lithography , 2004 .

[33]  Bharat Bhushan,et al.  Adhesion and friction properties of polymers in microfluidic devices , 2005 .

[34]  Holger Schönherr,et al.  Quantitative nanotribology by AFM: a novel universal calibration platform. , 2006, Langmuir : the ACS journal of surfaces and colloids.

[35]  Y. Hirai,et al.  Defect analysis in thermal nanoimprint lithography , 2003 .