Compressive strength and microstructure of alkali-activated fly ash/slag binders at high temperature

Abstract This paper reports the results of the compressive strength and microstructure of various alkali-activated binders at elevated temperatures of 300 and 600 °C. The binders were prepared by alkali-activated low calcium fly ash/ground granulated blast-furnace slag at ratios of 100/0, 50/50, 10/90 and 0/100 wt.%. Specimens free of loading were heated to a pre-fixed temperature by keeping the furnace temperature constant until the specimens reached a steady state. Then the specimen was loaded to failure while hot. XRD, SEM and FTIR techniques were used to investigate the microstructural changes after the thermal exposure. The fly ash-based specimen shows an increase in strength at 600 °C. On the other hand, the slag-based specimen gives the worst high-temperature performance particularly at a temperature of 300 °C as compared to ordinary Portland cement binder. This contrasting behaviour of binders is due to their different binder formulation which gives rise to various phase transformations at elevated temperatures. The effects of these transformations on the compressive strength are discussed on the basis of experimental results.

[1]  W. Duan,et al.  Effects of mineral admixtures and lime on disintegration of alkali-activated slag exposed to 50 °C , 2014 .

[2]  A. V. Riessen,et al.  Bayer-geopolymers: An exploration of synergy between the alumina and geopolymer industries , 2013 .

[3]  Ran Huang,et al.  Binding mechanism and properties of alkali-activated fly ash/slag mortars , 2013 .

[4]  W. Rickard,et al.  Performance of solid and cellular structured fly ash geopolymers exposed to a simulated fire , 2014 .

[5]  Donald W Breck,et al.  Zeolite Molecular Sieves: Structure, Chemistry, and Use , 1974 .

[6]  J. Sanjayan,et al.  Behavior of combined fly ash/slag‐based geopolymers when exposed to high temperatures , 2009 .

[7]  G. Kürklü,et al.  The effect of high temperature on the design of blast furnace slag and coarse fly ash-based geopolymer mortar , 2016 .

[8]  A. H. Korayem,et al.  Damping and microstructure of fly ash-based geopolymers , 2012, Journal of Materials Science.

[9]  M. Weil,et al.  The influence of calcium content on the structure and thermal performance of fly ash based geopolymers , 2007 .

[10]  Erdogan Ozbay,et al.  Microstructural alteration of alkali activated slag mortars depend on exposed high temperature level , 2016 .

[11]  A. Fernández-Jiménez,et al.  New Cementitious Materials Based on Alkali-Activated Fly Ash: Performance at High Temperatures , 2008 .

[12]  Jay G. Sanjayan,et al.  The properties of fly ash based geopolymer mortars made with dune sand , 2016 .

[13]  J. Sanjayan,et al.  Effect of strain rate on strength properties of low-calcium fly-ash-based geopolymer mortar under dry condition , 2013, Arabian Journal of Geosciences.

[14]  M. R. Bhutta,et al.  Performance of blended ash geopolymer concrete at elevated temperatures , 2015 .

[15]  J. Deventer,et al.  Microstructural changes in alkali activated fly ash/slag geopolymers with sulfate exposure , 2013 .

[16]  Kyung-Taek Koh,et al.  The mechanical properties of fly ash-based geopolymer concrete with alkaline activators , 2013 .

[17]  Prabir Sarker,et al.  Effect of GGBFS on setting, workability and early strength properties of fly ash geopolymer concrete cured in ambient condition , 2014 .

[18]  P. Gambarova,et al.  Thermo-mechanical behavior of baritic concrete exposed to high temperature , 2014 .

[19]  Robert Černý,et al.  Alkali-activated aluminosilicate composite with heat-resistant lightweight aggregates exposed to high temperatures: Mechanical and water transport properties , 2010 .

[20]  Ulrich Schneider,et al.  Compressive strength for service and accident conditions , 1995 .

[21]  H. Manzano,et al.  A model for the C-A-S-H gel formed in alkali-activated slag cements , 2011 .

[22]  Prabir Sarker,et al.  Fire endurance of steel reinforced fly ash geopolymer concrete elements , 2015 .

[23]  J. Sanjayan,et al.  Factors influencing softening temperature and hot-strength of geopolymers , 2012 .

[24]  Faiz Shaikh,et al.  Compressive strength of fly‐ash‐based geopolymer concrete at elevated temperatures , 2015 .

[25]  J. Sanjayan,et al.  Residual strength properties of sodium silicate alkali activated slag paste exposed to elevated temperatures , 2010 .

[26]  Venkatesh Kodur,et al.  Thermal behavior and mechanical properties of geopolymer mortar after exposure to elevated temperatures , 2016 .

[27]  Sifeng Liu,et al.  Influence of Slag as Additive on Compressive Strength of Fly Ash-Based Geopolymer , 2007 .

[28]  Longtu Li,et al.  A review: The comparison between alkali-activated slag (Si + Ca) and metakaolin (Si + Al) cements , 2010 .

[29]  P. Rovnaník,et al.  Characterization of alkali activated slag paste after exposure to high temperatures , 2013 .

[30]  A. Rashad.  A comprehensive overview about the influence of different admixtures and additives on the properties of alkali-activated fly ash , 2014 .

[31]  M. C. Alonso,et al.  Microstructure development in mixes of calcium aluminate cement with silica fume or fly ash , 2009 .

[32]  Z. Tao,et al.  In Situ Elevated Temperature Testing of Fly Ash Based Geopolymer Composites , 2016, Materials.

[33]  Z. Tao,et al.  High temperature performance of mortars containing fine glass powders , 2017 .

[34]  H. Lee,et al.  Reactivity and reaction products of alkali-activated, fly ash/slag paste , 2015 .