An evaluation of the lap-shear test for Sn-rich solder/Cu couples: Experiments and simulation

The lap-shear technique is commonly used to evaluate the shear, creep, and thermal fatigue behavior of solder joints. We have conducted a parametric experimental and modeling study, on the effect of testing and geometrical parameters on solder/copper joint response in lap-shear. It was shown that the farfield applied strain is quite different from the actual solder strain (measured optically). Subtraction of the deformation of the Cu substrate provides a reasonable approximation of the solder strain in the elastic regime, but not in the plastic regime. Solder joint thickness has a profound effect on joint response. The solder response moves progressively closer to “true” shear response with increasing joint thickness. Numerical modeling using finite-element analyses were performed to rationalize the experimental findings. The same lap-shear configuration was used in the simulation. The input response for solder was based on the experimental tensile test result on bulk specimens. The calculated shear response, using both the commonly adopted far-field measure and the actual shear strain in solder, was found to be consistent with the trends observed in the lap-shear experiments. The geometric features were further explored to provide physical insight into the problem. Deformation of the substrate was found to greatly influence the shear behavior of the solder.

[1]  William J. Plumbridge,et al.  Damage produced in model solder (Sn-37Pb) joints during thermomechanical cycling , 2003 .

[2]  S. Krenk,et al.  Fatigue analysis and testing of adhesive joints , 1996 .

[3]  Gang Li,et al.  Nonlinear finite element analysis of stress and strain distributions across the adhesive thickness in composite single-lap joints , 1999 .

[4]  Nikhilesh Chawla,et al.  Influence of initial morphology and thickness of Cu6Sn5 and Cu3Sn intermetallics on growth and evolution during thermal aging of Sn-Ag solder/Cu joints , 2003 .

[5]  D. R. Frear,et al.  Parameters affecting thermal fatigue behavior of 60Sn-40Pb solder joints , 1989 .

[6]  C. Wright,et al.  The Effect of Solid-State Reactions Upon Solder Lap Shear Strength , 1977 .

[7]  D. Updike,et al.  Bending and Shear Deformation Effects in Lap Joints , 1981 .

[8]  Wing Kong Chiu,et al.  A numerical study of adhesively bonded lap joints , 1992 .

[9]  W. J. Plumbridge,et al.  Solders in electronics , 1996, Journal of Materials Science.

[10]  D. R. Frear,et al.  Materials issues in area-array microelectronic packaging , 1999 .

[11]  D. Barnard,et al.  A shear test method to measure shear strength of metallic materials and solder joints using small specimens , 1999 .

[12]  Nikhilesh Chawla,et al.  Effects of cooling rate on the microstructure and tensile behavior of a Sn-3.5wt.%Ag solder , 2003 .

[13]  Nikhilesh Chawla,et al.  The effects of cooling rate on microstructure and mechanical behavior of Sn-3.5Ag solder , 2003 .

[14]  B. A. Cook,et al.  Shear deformation in Sn-3.5Ag and Sn-3.6Ag-1.0Cu solder joints subjected to asymmetric four-point bend tests , 2001 .

[15]  G. Smith,et al.  Cyclic stress durability testing of lap shear joints exposed to hot-wet conditions , 2000 .

[16]  F. Shieu,et al.  Microstructure and shear strength of a Au–In microjoint , 2000 .

[17]  D. W. Oplinger,et al.  Effects of adherend deflections in single lap joints , 1994 .

[18]  Paul T. Vianco,et al.  Properties of ternary Sn-Ag-Bi solder alloys: Part II—Wettability and mechanical properties analyses , 1999 .

[19]  M. Poech,et al.  A Finite-Element and Experimental Analysis of Stress Distribution in Various Shear Tests for Solder Joints , 1998 .

[20]  D. B. Knorr,et al.  The effect of aging on microstructure, room temperature deformation, and fracture of Sn-Bi/Cu solder joints , 1994 .

[21]  King-Ning Tu,et al.  Interdiffusion and Reaction in Bimetallic Cu-Sn Thin Films , 1973 .

[22]  T. Guess,et al.  COMPARISON OF LAP SHEAR TEST SPECIMENS , 1977 .

[23]  T. Chou,et al.  Characterization of Interlaminar Shear Strength of Ceramic Matrix Composites , 1993 .

[24]  Shiuh-Chuan Her,et al.  Stress analysis of adhesively-bonded lap joints , 1999 .

[25]  Lin Chien-Chang,et al.  A finite element model of single-lap adhesive joints , 1993 .

[26]  David A. Dillard,et al.  The cracked lap shear specimen revisited—a closed form solution , 1996 .