An Optical Frequency Comb Tied to GPS for Laser Frequency/Wavelength Calibration

Optical frequency combs can be employed over a broad spectral range to calibrate laser frequency or vacuum wavelength. This article describes procedures and techniques utilized in the Precision Engineering Division of NIST (National Institute of Standards and Technology) for comb-based calibration of laser wavelength, including a discussion of ancillary measurements such as determining the mode order. The underlying purpose of these calibrations is to provide traceable standards in support of length measurement. The relative uncertainty needed to fulfill this goal is typically 10−8 and never below 10−12, very modest requirements compared to the capabilities of comb-based frequency metrology. In this accuracy range the Global Positioning System (GPS) serves as an excellent frequency reference that can provide the traceable underpinning of the measurement. This article describes techniques that can be used to completely characterize measurement errors in a GPS-based comb system and thus achieve full confidence in measurement results.

[1]  P. Maddaloni,et al.  Optical comb generators for laser frequency measurement , 2009 .

[2]  M. Lombardi,et al.  Characterizing the performance of GPS disciplined oscillators with respect to UTC(NIT) , 2005, Proceedings of the 2005 IEEE International Frequency Control Symposium and Exposition, 2005..

[3]  S. Johansson,et al.  New frequency counting principle improves resolution , 2005, Proceedings of the 20th European Frequency and Time Forum.

[4]  T. Hänsch,et al.  Optical frequency metrology , 2002, Nature.

[5]  Michael A. Lombardi,et al.  The Use of GPS Disciplined Oscillators as Primary Frequency Standards for Calibration and Metrology Laboratories , 2008 .

[6]  M. Zucco,et al.  10−12 level reproducibility of an iodine-stabilized He–Ne laser endorsed by absolute frequency measurements in the BIPM and UME , 2006 .

[7]  C. Tilford.  Analytical procedure for determining lengths from fractional fringes. , 1977, Applied optics.

[8]  Albrecht Bartels,et al.  Optical frequency measurements with the global positioning system: tests with an iodine-stabilized He-Ne laser. , 2005, Applied optics.

[9]  Gesine Grosche,et al.  Phase-locked two-branch erbium-doped fiber laser system for long-term precision measurements of optical frequencies. , 2004, Optics express.

[10]  Robert S. Windeler,et al.  A new method to determine the absolute mode number of a mode-locked femtosecond-laser comb used for absolute optical frequency measurements , 2003 .

[11]  Liang Lu,et al.  Calibrating Laser Vacuum Wavelength with a GPS-based Optical Frequency Comb , 2007 .

[12]  Q. Gong,et al.  Exact frequency comb mode number determination in precision optical frequency measurements , 2007 .

[13]  Andrew N. Novick,et al.  Time and Frequency Measurements Using the Global Positioning System , 2001 .

[14]  L. Robertsson,et al.  A collinear self-referencing set-up for control of the carrier-envelope offset frequency in Ti : sapphire femtosecond laser frequency combs , 2005 .

[15]  Andrew N. Novick,et al.  Time and Frequency Measurements Using the Global Positioning System (GPS) , 2001 .

[16]  Gunnar Ritt,et al.  Laser frequency offset locking using a side of filter technique , 2004 .

[17]  J. Fowler,et al.  Journal of Research of the National Institute of Standards and Technology INFORMATION TECHNOLOGY FOR ENGINEERING AND MANUFACTURING Gaithersburg , MD June 12-13 , 2000 , 2000 .

[18]  S. Dawkins,et al.  Considerations on the Measurement of the Stability of Oscillators with Frequency Counters , 2007, 2007 IEEE International Frequency Control Symposium Joint with the 21st European Frequency and Time Forum.

[19]  Andrew Lewis,et al.  Advice from the CCL on the use of unstabilized lasers as standards of wavelength: the helium–neon laser at 633 nm , 2009 .