Finite element modeling of capacitive micromachined ultrasonic transducers

Transducers based on piezoelectric crystals dominate the biomedical ultrasonic imaging field. However, fabrication difficulties for piezoelectric transducers limit their usage for complex imaging modalities such as 2D imaging, high frequency imaging, and forward looking intravascular imaging. Capacitive micromachined ultrasonic transducers (CMUTs) have been proposed to overcome these limitations and they offer competitive advantages in terms of bandwidth and dynamic range. Further, the ease of fabrication enables manufacturing of complex array geometries. A CMUT transducer is composed of many electrostatically actuated membranes. Earlier analysis of these devices concentrated on an equivalent circuit approach, which assumed the motion of the membrane was approximated by a parallel plate capacitor. Finite element analysis is required for more accurate results. In this paper, we present the finite element model developed to evaluate the performance of the CMUTs. The model is composed of a membrane radiating into immersion medium. Electrostatic actuation is added on using electromechanical elements. Symmetry boundary conditions are imposed around the sidewalls of the finite element mesh, so that the model reflects the properties of a cell driven with the same phase as its neighboring membranes in an infinitely large array. Absorbing boundaries are implemented one wavelength away from the membrane to avoid reflections from the end of the finite element mesh. Using the model, we optimized the membrane radius, membrane thickness and gap height. Our optimized designed yielded a center frequency of 13 MHz with hundred percent bandwidth. A maximum output pressure of 20 kPascal per volt was obtained.

[1]  John Mould,et al.  Time-domain models of MUT array cross-talk in silicon substrates , 2000, 2000 IEEE Ultrasonics Symposium. Proceedings. An International Symposium (Cat. No.00CH37121).

[2]  H. Saunders,et al.  Acoustics: An Introduction to Its Physical Principles and Applications , 1984 .

[3]  W. Benecke,et al.  IMPROVED EQUIVALENT CIRCUIT AND FINITE ELEMENT METHOD MODELING OF CAPACITIVE MICROMACHINED ULTRASONIC TRANSDUCERS , 2003 .

[4]  B. Khuri-Yakub,et al.  Capacitive micromachined ultrasonic transducers: next-generation arrays for acoustic imaging? , 2002, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[5]  B.T. Khuri-Yakub,et al.  A new regime for operating capacitive micromachined ultrasonic transducers , 2003, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[6]  B.T. Khuri-Yakub,et al.  Calculation and measurement of electromechanical coupling coefficient of capacitive micromachined ultrasonic transducers , 2003, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[7]  B. Bayram,et al.  Influence of the electrode size and location on the performance of a CMUT [US transducer] , 2001, 2001 IEEE Ultrasonics Symposium. Proceedings. An International Symposium (Cat. No.01CH37263).

[8]  R.M.E.J. Spiering,et al.  On-chip decoupling zone for package-stress reduction , 1991, TRANSDUCERS '91: 1991 International Conference on Solid-State Sensors and Actuators. Digest of Technical Papers.

[9]  Manfred Kaltenbacher,et al.  3D simulation of controlled micromachined capacitive ultrasound transducers , 1999, 1999 IEEE Ultrasonics Symposium. Proceedings. International Symposium (Cat. No.99CH37027).

[10]  Edward Hæggström,et al.  Fabricating capacitive micromachined ultrasonic transducers with wafer-bonding technology , 2003 .

[11]  W. Benecke,et al.  Derivation of a 1D CMUT model from FEM results for linear and nonlinear equivalent circuit simulation , 2003, IEEE Symposium on Ultrasonics, 2003.

[12]  B. Khuri-Yakub,et al.  Surface micromachined capacitive ultrasonic transducers , 1998, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[13]  Sylvain Ballandras,et al.  Simulation of cMUT radiating in water using a mixed finite element/boundary element approach , 2002, 2002 IEEE Ultrasonics Symposium, 2002. Proceedings..

[14]  Miko Elwenspoek,et al.  On-chip decoupling zone for package-stress reduction , 1991 .

[15]  I. Ladabaum,et al.  Theory and analysis of electrode size optimization for capacitive microfabricated ultrasonic transducers , 1999, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[16]  B.T. Khuri-Yakub,et al.  Finite element analysis of underwater capacitor micromachined ultrasonic transducers , 2002, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[17]  B. Khuri-Yakub,et al.  Improved equivalent circuit and finite element method modeling of capacitive micromachined ultrasonic transducers , 2003, IEEE Symposium on Ultrasonics, 2003.