Effect of Coolant Pulsation on Film Cooling Performance on Flat Plate

[1]  M. Rajabi Zargarabadi,et al.  Effect of pulsating injection and mainstream attack angle on film cooling performance of a gas turbine blade , 2020 .

[2]  Xiang I. A. Yang,et al.  Grid-point and time-step requirements for direct numerical simulation and large-eddy simulation , 2020, Physics of Fluids.

[3]  G. Xie,et al.  Combined-Hole Film Cooling Designs Based on the Construction of Antikidney Vortex Structure: A Review , 2020, Journal of Heat Transfer.

[4]  Chunhua Wang,et al.  Study on trench film cooling on turbine vane by large-eddy simulation , 2020 .

[5]  Chunhua Wang,et al.  Recent advances in film cooling enhancement: A review , 2020 .

[6]  Xiang Luo,et al.  Effect of film hole geometry and blowing ratio on film cooling performance , 2020 .

[7]  S. Wang,et al.  Large eddy simulation of the trenched film cooling hole with different compound angles and coolant inflow orientation effects , 2019 .

[8]  You Liu,et al.  Transient simulation of pulsed purge film cooling on flow and thermal characteristics of a turbine endwall , 2019, Applied Thermal Engineering.

[9]  Xiaokai Sun,et al.  Uncertainty analysis of trench film cooling on flat plate , 2019, Applied Thermal Engineering.

[10]  Guozhan Li,et al.  Large eddy simulation of film cooling flow from cylindrical hole with dielectric barrier discharge plasma actuators , 2019, Applied Thermal Engineering.

[11]  Ying Huang,et al.  Large eddy simulation of film cooling flow from a fanshaped hole , 2018 .

[12]  M. Fénot,et al.  Influence of Coolant Jet Pulsation on the Convective Film Cooling of an Adiabatic Wall , 2017 .

[13]  Toshihiko Takahashi,et al.  Large-eddy simulation of an inclined round jet issuing into a crossflow , 2014 .

[14]  Hessam Babaee,et al.  Optimization of Forcing Parameters of Film Cooling Effectiveness , 2013 .

[15]  J. Rutledge,et al.  Influence of Film Cooling Unsteadiness on Turbine Blade Leading Edge Heat Flux , 2012 .

[16]  F. Muldoon,et al.  DNS study of pulsed film cooling for enhanced cooling effectiveness , 2009 .

[17]  Wolfgang Schröder,et al.  Large-eddy simulation of film cooling flows at density gradients , 2008 .

[18]  S. M. Coulthard,et al.  Effect of Jet Pulsing on Film Cooling—Part II: Heat Transfer Results , 2007 .

[19]  Ralph J. Volino,et al.  Effect of Jet Pulsing on Film Cooling—Part I: Effectiveness and Flow-Field Temperature Results , 2007 .

[20]  Wolfgang Schröder,et al.  Large-eddy simulations of film cooling flows , 2006 .

[21]  Srinath V. Ekkad,et al.  Effect of Jet Pulsation and Duty Cycle on Film Cooling From a Single Jet on a Leading Edge Model , 2006 .

[22]  Sumanta Acharya,et al.  Large Eddy Simulation of Film Cooling Flow From an Inclined Cylindrical Jet , 2003 .

[23]  Phillip M. Ligrani,et al.  Effects of Bulk Flow Pulsations on Film Cooling With Compound Angle Holes: Heat Transfer Coefficient Ratio and Heat Flux Ratio , 2001 .

[24]  P. Ligrani,et al.  Effects of Bulk Flow Pulsations on Film Cooling From Different Length Injection Holes at Different Blowing Ratios , 1998 .

[25]  M. Kurosaka,et al.  Kidney and anti-kidney vortices in crossflow jets , 1997, Journal of Fluid Mechanics.

[26]  Phillip M. Ligrani,et al.  Bulk flow pulsations and film cooling—I. Injectant behavior , 1996 .

[27]  J. Bons,et al.  The effect of unsteadiness on film cooling effectiveness , 1995 .

[28]  P. Moin,et al.  Eddies, streams, and convergence zones in turbulent flows , 1988 .

[29]  J. Smagorinsky,et al.  GENERAL CIRCULATION EXPERIMENTS WITH THE PRIMITIVE EQUATIONS , 1963 .

[30]  Chunhua Wang,et al.  Large eddy simulation of film cooling on turbine vane , 2019, Journal of Thermal Science and Technology.

[31]  D. H. Leedom,et al.  Large Eddy Simulations of Film Cooling Flow Fields From Cylindrical and Shaped Holes , 2008 .

[32]  Robert J. Moffat,et al.  Describing the Uncertainties in Experimental Results , 1988 .