A Simulator Study of Friction in Total Replacement Hip Joints

Frictional behaviour of 22 different femoral head-acetabular cup combinations was studied on a new servo-hydraulic microcomputer-controlled hip joint simulator using various flexion-extension angle and superior-inferior load set value waveforms and using distilled water at 37 ± 1°C as lubricant. Six different head materials were included in the study, whereas all cups were ultra-high molecular weight polyethylene (UHMWPE). Most head-cup combinations studied are commercially available. No distinctly superior joint design can he pointed out, but the frictional behaviour of alumina ceramic against UHMWPE proved overall most favourable (μmin was 0.02), whereas that of non-ion-implanted titanium alloy Ti-6Al-4V against UHMWPE proved strikingly poor (μmax was 0.15). The lowest frictional torque was in 22 mm joints, but frictional torque did not always increase straightforwardly with increasing diameter of the femoral head. The measurements form an extensive comparison between a wide variety of head-cup combinations. The simulator is apparently a useful instrument in the study of frictional behaviour of new designs, materials, surface treatments and coatings that are frequently introduced.

[1]  Duncan Dowson,et al.  The Frictional Behavior of Human Synovial Joints—Part I: Natural Joints , 1975 .

[2]  G. Smidt,et al.  Measurement of hip joint motion during walking , 1969 .

[3]  A Cappozzo,et al.  Evaluation of hip arthroprostheses by means of body environment simulators. , 1977, Journal of biomedical materials research.

[4]  M. Ungethüm.  Requirements of Operational Tests and Test Results in Total Hip and Knee Arthroplasty , 1976 .

[5]  J. Kabo,et al.  Frictional torque in surface and conventional hip replacement. , 1983, The Journal of bone and joint surgery. American volume.

[6]  P. Sioshansi,et al.  Wear improvement of surgical titanium alloys by ion implantation , 1985 .

[7]  A. Unsworth,et al.  Frictional properties of artificial hip joints. , 1988, Engineering in Medicine.

[8]  A. Unsworth.  The effects of lubrication in hip joint prostheses. , 1978, Physics in medicine and biology.

[9]  James A. Davidson,et al.  The effect of human synovial lubricant and temperature on in-vitro friction and torque of the prosthetic hip , 1988 .

[10]  J. Davidson,et al.  Wear, creep, and frictional heating of femoral implant articulating surfaces and the effect on long-term performance--Part II, Friction, heating, and torque. , 1988, Journal of biomedical materials research.

[11]  J. Galante,et al.  Wear in total hip prostheses. An experimental evaluation of candidate materials. , 1972, Acta orthopaedica Scandinavica. Supplementum.

[12]  S. Simon,et al.  Lubrication Mechanism of Hip Joint Replacement Prostheses , 1972 .

[13]  D. Dowson,et al.  An Experimental Study of Friction and Lubrication in Hip Prostheses , 1979 .

[14]  S. Simon,et al.  "Stiction-friction" of total hip prostheses and its relationship to loosening. , 1975, The Journal of bone and joint surgery. American volume.

[15]  Wear behaviour of medical engineering materials , 1975 .

[16]  G. Smidt,et al.  Measurement of hip-joint motion during walking. Evaluation of an electrogoniometric method. , 1969, The Journal of bone and joint surgery. American volume.

[17]  P. S. Walker,et al.  Comparison of the Bearing Performance of Normal and Artificial Human Joints , 1973 .

[18]  J. G. Andrews,et al.  A biomechanical investigation of the human hip. , 1978, Journal of biomechanics.

[19]  M. Freeman,et al.  Laboratory tests on total joint replacement prostheses. , 1973, The Journal of bone and joint surgery. British volume.

[20]  P. Walker,et al.  The measurement and effects of friction and wear in artificial hip joints. , 1973, Journal of biomedical materials research.

[21]  Simulated studies of wear and friction in total hip prosthesis components with various ball sizes and surface finishes , 1976 .