Experimental and numerical investigation of fiberglass rod joint on mechanical characteristic and failure mode in high water-content wells

ABSTRACT At present, fiberglass sucker rod has been gradually utilized in low permeability reservoirs because of their high strength and strong corrosion resistance. However, the bonding joint of fiberglass sucker rod in high water-content well is particularly prone to break and fall off, which influences the service life and construction safety of recovery operation. Current researches mainly focused on the bonding strength at room temperature, and less consideration was given to the residual strength and failure pattern under immersion. This paper proposed a novel diffusion-structure finite element model (FEM) based on transient dynamic method to simulate the process of water into the joint, and the life-death element method was adopted to study the progressive damage of bonding joints verified by indoor experiment in order to predict residual failure strength and obtain failure mode in submerged environment. As immersion duration extended, the results illustrated that a) the cohesive failure gradually became main failure; b) the maximum von Mises stress, shear stress, and end deformation of bonded joint increased and the maximum interfacial stress barely unchanged within the range of 5%; c) the numerically predicted strength decreased from 21.8 to 11.5 MPa, which was in good agreement with the experimental results within a deviation of 8%.

[1]  R. Wu,et al.  A general numerical model for predicting the flexural behavior of hybrid FRP-steel reinforced concrete beams , 2021, Engineering Structures.

[2]  K. Lundgren,et al.  Numerical assessment of bond-slip relationships for naturally corroded plain reinforcement bars in concrete beams , 2021, Engineering Structures.

[3]  Yongkang Zhang,et al.  Effect of laser processing microstructure on the bonding strength and failure mode of 7075-T6 aluminum alloy adhesive joints , 2021 .

[4]  Jian Wang,et al.  Experimental investigation of clinching CFRP/aluminum alloy sheet with prepreg sandwich structure , 2020 .

[5]  Houbu Li,et al.  Failure analysis of a sucker rod fracture in an oilfield , 2020 .

[6]  Hai Wang,et al.  A novel approach for the interfacial stress analysis of composite adhesively bonded joints , 2019, Composites Science and Technology.

[7]  Lianyong Feng,et al.  Energy return on energy, carbon, and water investment in oil and gas resource extraction: Methods and applications to the Daqing and Shengli oilfields , 2019, Energy Policy.

[8]  B. O. Baba,et al.  Mechanical response of adhesively bonded composite joints subjected to vibration load and axial impact , 2019, Composites Part B: Engineering.

[9]  A. Khaloo,et al.  Dynamic performance of concrete slabs reinforced with steel and GFRP bars under impact loading , 2019, Engineering Structures.

[10]  Hui Li,et al.  Combined effects of temperature, hydraulic pressure and salty concentration on the water uptake and mechanical properties of a carbon/glass fibers hybrid rod in salty solutions , 2019, Polymer Testing.

[11]  Jingxin Na,et al.  Effect of alternating load on the residual strength of environmentally aged adhesively bonded CFRP-aluminum alloy joints , 2019, Composites Part B: Engineering.

[12]  Joaquim Teixeira de Assis,et al.  Numerical and experimental analysis of bonded joints with combined loading , 2019, International Journal of Adhesion and Adhesives.

[13]  Duanjun Xu,et al.  Damage mode identification of adhesive composite joints under hygrothermal environment using acoustic emission and machine learning , 2019, Composite Structures.

[14]  E. Ferrier,et al.  Mechanical behaviour of glued-in rods (carbon and glass fibre-reinforced polymers) for timber structures—An analytical and experimental study , 2019, Composite Structures.

[15]  K. Tserpes,et al.  Fatigue crack growth characterization in adhesive CFRP joints , 2019, Composite Structures.

[16]  M. Nasser,et al.  Effect of temperature and fluid speed on the corrosion behavior of carbon steel pipeline in Qatari oilfield produced water , 2018 .

[17]  Xiaoquan Cheng,et al.  An investigation of hygrothermal effects on adhesive materials and double lap shear joints of CFRP composite laminates , 2016 .

[18]  K. N. Rai,et al.  Fractional single-phase-lagging heat conduction model for describing anomalous diffusion , 2016 .

[19]  F. Ascione.  The influence of adhesion defects on the collapse of FRP adhesive joints , 2016 .

[20]  P. Marimuthu,et al.  Multi-response optimization of turning parameters for machining glass fiber–reinforced plastic composite rod , 2015 .

[21]  K. Tserpes,et al.  Mode-I, mode-II and mixed-mode I+II fracture behavior of composite bonded joints: Experimental characterization and numerical simulation , 2015 .

[22]  J. Du,et al.  Corrosion behavior of X65 carbon steel in simulated oilfield produced water , 2015 .

[23]  D. Duan,et al.  Failure mechanism of sucker rod coupling , 2014 .

[24]  J. K. Spelt,et al.  Adherend thickness influence on fatigue behavior and fatigue failure prediction of adhesively bonded joints , 2013 .

[25]  L.F.M. da Silva,et al.  Mixed-mode I + II fatigue/fracture characterization of composite bonded joints using the Single-Leg Bending test , 2013 .

[26]  R. Palazzetti,et al.  Failure analysis of adhesively bonded joints in composite materials , 2012 .

[27]  H. Nevzat Özgüven,et al.  Dynamic Characterization of Structural Joints Using FRF Decoupling , 2012 .

[28]  Yaoguang Qi,et al.  A modern approach to the selection of sucker rod pumping systems in CBM wells , 2011 .

[29]  P. Hammond,et al.  Sorption isotherms, sorption enthalpies, diffusion coefficients and permeabilities of water in a multilayer PEO/PAA polymer film using the quartz crystal microbalance/heat conduction calorimeter , 2006 .

[30]  M. Bowditch,et al.  The durability of adhesive joints in the presence of water , 1996 .