Model for a multiple-step deep Si etch process

A multiple-step deep Si etch process involving separate etching and polymerization steps is often employed for fabrication of microelectromechanical systems, microfluidics devices, and other assorted deep structures in Si. An integrated plasma equipment-feature evolution model for this multiple-step deep Si etch process is described in this article. In the two-dimensional plasma equipment model, the etching (SF6/O2) and polymerization [octafluorocyclobutane(c-C4F8)] chemistries are separately simulated assuming steady-state conditions. The outputs of the equipment simulations are combined in a string-based feature profile evolution model to simulate the multiple-step deep Si etch process. In the plasma equipment models, detailed gas phase plasma chemistries including electron impact processes, ion–molecule reactions, and neutral chemistry have been considered for both the etching and polymerization gas mixtures. The plasma–surface interaction mechanisms in the feature profile evolution model are based on qualitative information available in literature and the correlation of modeling results with experimental data. Under the relevant operating conditions, F is assumed to be the primary Si etchant, film deposition in c-C4F8 is due to sticking of C, CF2, and C2F4 under ion bombardment, and the polymer is etched by energetic ions through physical sputtering. It is demonstrated that predictions of the resulting model are in close agreement with experiments. The validated model is used to understand the dynamics of the multiple-step deep Si etch process and how etching characteristics can be controlled using a variety of process parameters. Etching characteristics have been found to be quite sensitive to gas pressure, coil power, bias power, and relative step time during both etching and polymerization processes. The Si etch rate and feature sidewall angle are coupled to each other over a wide range of operating conditions.A multiple-step deep Si etch process involving separate etching and polymerization steps is often employed for fabrication of microelectromechanical systems, microfluidics devices, and other assorted deep structures in Si. An integrated plasma equipment-feature evolution model for this multiple-step deep Si etch process is described in this article. In the two-dimensional plasma equipment model, the etching (SF6/O2) and polymerization [octafluorocyclobutane(c-C4F8)] chemistries are separately simulated assuming steady-state conditions. The outputs of the equipment simulations are combined in a string-based feature profile evolution model to simulate the multiple-step deep Si etch process. In the plasma equipment models, detailed gas phase plasma chemistries including electron impact processes, ion–molecule reactions, and neutral chemistry have been considered for both the etching and polymerization gas mixtures. The plasma–surface interaction mechanisms in the feature profile evolution model are based on ...

[1]  S. Rauf,et al.  Argon metastable densities in radio frequency Ar, Ar/O2 and Ar/CF4 electrical discharges , 1997 .

[2]  C. Pomot,et al.  The etching of silicon in diluted SF6 plasmas: Correlation between the flux of incident species and the etching kinetics , 1987 .

[3]  J. Arnold,et al.  Simulation of surface topography evolution during plasma etching by the method of characteristics , 1994 .

[4]  S. Rauf,et al.  Model for an inductively coupled Ar/c-C4F8 plasma discharge , 2002 .

[5]  D. K. Davies,et al.  Dielectric properties for SF6 and SF6 mixtures predicted from basic data , 1979 .

[6]  J. Booth,et al.  CF2 PRODUCTION AND LOSS MECHANISMS IN FLUOROCARBON DISCHARGES : FLUORINE-POOR CONDITIONS AND POLYMERIZATION , 1999 .

[7]  C. Winstead,et al.  Electron collisions with octafluorocyclobutane, c-C4F8 , 2001 .

[8]  R. J. Van Brunt,et al.  Electron‐transport, ionization, attachment, and dissociation coefficients in SF6 and its mixtures , 1988 .

[9]  M. Hori,et al.  Precursors of fluorocarbon film growth studied by mass spectrometry , 2000 .

[10]  James K. Olthoff,et al.  Electron Interactions With SF6 , 2000 .

[11]  M. Misakian,et al.  Ion fluxes and energies in inductively coupled radio-frequency discharges containing C2F6 and c-C4F8 , 2000 .

[12]  A. Garscadden,et al.  Ion chemistry in octafluorocyclobutane, c-C4F8 , 1998 .

[13]  Samuel Lee Miller,et al.  Silicon nitride membranes for filtration and separation , 1999, MOEMS-MEMS.

[14]  N. Sadeghi,et al.  CFx radical production and loss in a CF4 reactive ion etching plasma: Fluorine rich conditions , 1999 .

[15]  B. Lehmann.  Notizen: Bildung negativer Ionen durch Elektronenstoß in SF6 unterhalb 25 eV , 1970 .

[16]  R. Laher,et al.  Updated excitation and ionization cross sections for electron impact on atomic oxygen. Technical report, 1 October 1987-29 February 1988 , 1988 .

[17]  Robert J. Hoekstra,et al.  Two‐dimensional modeling of high plasma density inductively coupled sources for materials processing , 1994 .

[18]  M. Hori,et al.  Surface reaction of CF2 radicals for fluorocarbon film formation in SiO2/Si selective etching process , 1998 .

[19]  D. Rapp,et al.  Total Cross Sections for Ionization and Attachment in Gases by Electron Impact. I. Positive Ionization , 1965 .

[20]  K. Becker,et al.  Electron impact ionization of the SF5 and SF3 free radicals , 1998 .

[21]  Gregory A. Hebner,et al.  An Inductively Coupled Plasma Source for the Gaseous Electronics Conference RF Reference Cell , 1995, Journal of research of the National Institute of Standards and Technology.

[22]  H. Sawin,et al.  Polysilicon Etching in SF 6 RF Discharges Characteristics and Diagnostic Measurements , 1986 .

[23]  Mark J. Kushner,et al.  Surface kinetics and plasma equipment model for Si etching by fluorocarbon plasmas , 2000 .

[24]  Kenneth C. Cadien,et al.  Plasma Etching of Silicon in SF 6 Experimental and Reactor Modeling Studies , 1990 .

[25]  T. Märk,et al.  Electron impact ionization cross sections of molecules , 1990 .

[26]  E. Krishnakumar,et al.  Cross-sections for electron impact ionization of O2 , 1992 .

[27]  M. A. Ali,et al.  Electron-impact total ionization cross sections of SFx(x = 1–5) , 2000 .

[28]  William J. Dauksher,et al.  Modeling and development of a deep silicon etch process for 200 mm election projection lithography mask fabrication , 2001 .

[29]  Ian Ronald Johnston,et al.  Recent advances in silicon etching for MEMS using the ASE™ process , 1999 .

[30]  T. Stański,et al.  Measurements of dissociative ionization cross section of SF6 by using double collector cycloidal mass spectrometer , 1983 .

[31]  C. J. Mogab,et al.  Plasma etching of Si and SiO2—The effect of oxygen additions to CF4 plasmas , 1978 .

[32]  Vincent M. Donnelly,et al.  The reaction of fluorine atoms with silicon , 1981 .

[33]  I. C. Plumb,et al.  Gas-phase reactions in plasmas of SF6 with O2: Reactions of F with SOF2 and SO2 and reactions of O with SOF2 , 1989 .

[34]  A. P. Hickman.  Approximate scaling formula for ion–ion mutual neutralization rates , 1979 .

[35]  H. Toyoda,et al.  Relative Cross Sections for Electron‐Impact Dissociation of SF6 into SFx (x = 1−3) Neutral Radicals , 1995 .

[36]  L. Kline,et al.  Electron and Chemical Kinetics in the Low-Pressure RF Discharge Etching of Silicon in SF6 , 1986, IEEE Transactions on Plasma Science.

[37]  K. Eisele.  SF 6, a Preferable Etchant for Plasma Etching Silicon , 1981 .

[38]  K. R. Ryan.  Aspects of the chemistry of SF6/O2 plasmas , 1989 .

[39]  I. C. Plumb,et al.  Gas-phase reactions in plasmas of SF6 with O2 in He , 1988 .

[40]  Stephen Hall,et al.  Etching 200-mm diameter SCALPEL masks with the ASE process , 2000, Advanced Lithography.

[41]  S. Rauf,et al.  Plasma abatement of perfluorocompounds in inductively coupled plasma reactors , 2000 .

[42]  Rida T. Farouki,et al.  A shock‐tracking algorithm for surface evolution under reactive‐ion etching , 1993 .

[43]  M. Hayashi,et al.  Calculation of electron swarm parameters in fluorine , 1983 .