Investigation on microstructure, surface properties and anti-wear performance of HVOF sprayed WC–CrC–Ni coatings modified by laser heat treatment

Abstract Laser heat (LH) treatment was found to be an effective method to alter the microstructure and mechanical properties of conventional coatings. In this investigation, the effects of laser scanning velocity on microstructure, microhardness and wear performance of high velocity oxygen fuel sprayed (HVOF) WC–CrC–Ni coatings during laser heating treatment were investigated. The results showed that the microstructure of the HVOF coatings changed greatly after the LH treatment. X-ray diffraction (XRD) patterns indicated that WC and Cr3C2, as primary phases, were present in both the HVOF- and LH-treated coatings, while only a small amount of Ni phase existed in the LH-treated coatings. With the post-treatment process of laser heating, a compact interface was found between the coating and substrate. When the laser scanning velocity decreased, the porosity and thickness of the LH-treated coatings decreased, leading to a gradual increase of microhardness. In the wear test, the friction and wear resistance of the coating were improved significantly with an optimal laser heating process (600 W power, 300 mm/min scanning velocity). The improvement can be attributed to the improved porosity and hardness, as well as the formation of oxide tribofilms.

[1]  J. Guilemany,et al.  The influence of gun transverse speed on electrochemical behaviour of thermally sprayed Cr3C2-NiCr coatings in 0.5 M H2SO4 solution , 2004 .

[2]  K. S. Kim,et al.  A study on HVOF coatings of micron and nano WC-Co powders , 2008 .

[3]  A. Ruff,et al.  Friction and wear properties of WC-Co and Mo-Mo2C based functionally graded materials , 2001 .

[4]  W. Hou,et al.  High performance amorphous steel coating prepared by HVOF thermal spraying , 2009 .

[5]  F. Stott,et al.  Crack-free densification of ceramics by laser surface treatment , 2006 .

[6]  Koshi Adachi,et al.  Wear of advanced ceramics , 2002 .

[7]  S. Kuroda,et al.  Sliding wear properties of HVOF sprayed WC–20%Cr3C2–7%Ni cermet coatings , 2007 .

[8]  E. Cappelli,et al.  WC–Co cutting tool surface modifications induced by pulsed laser treatment , 1999 .

[9]  G. Montavon,et al.  Structure and wear behaviour of HVOF sprayed Cr3C2–NiCr and WC–Co coatings , 2003 .

[10]  J. Guilemany,et al.  Structural characterization of laser-treated Cr 3 C 2 –NiCr coatings , 2001 .

[11]  Zhu Liu,et al.  Improving corrosion and wear performance of HVOF-sprayed Inconel 625 and WC-Inconel 625 coatings by high power diode laser treatments , 2007 .

[12]  Jorma Vihinen,et al.  Improving corrosion properties of high-velocity oxy-fuel sprayed inconel 625 by using a high-power continuous wave neodymium-doped yttrium aluminum garnet laser , 2000 .

[13]  Qiaoqin Yang,et al.  Effect of carbide grain size on microstructure and sliding wear behavior of HVOF-sprayed WC–12% Co coatings , 2003 .

[14]  H. Kato.  Severe–mild wear transition by supply of oxide particles on sliding surface , 2003 .

[15]  S. L. Semiatin,et al.  The effect of laser power and traverse speed on microstructure, porosity, and build height in laser-deposited Ti-6Al-4V , 2000 .

[16]  W. Fang,et al.  Characterization of microstructure and surface properties of hybrid coatings of WC–CoCr prepared by laser heat treatment and high velocity oxygen fuel spraying , 2008 .

[17]  B. Yilbas,et al.  Laser treatment of cemented carbide cutting tool , 2007 .