Additive Manufacturing of Shaped Profile Windings for Minimal AC Loss in Electrical Machines

Metal additive manufacturing enables production of copper and aluminium parts exhibiting unmatched geometric freedom, giving rise to new possibilities in the winding design of electrical machines and wound passive components. Early adopters of additive manufacturing are primarily concerned with improving power-density or efficiency by increasing slot fill-factor, optimizing end-winding topology or incorporating cooling channels into the conductors. In this article, a method of minimizing the elevated ac loss present in open slot electrical machine topologies is presented, in which individual conductor profiles are shaped according to their magnetic environment. Such shaped profile windings are shown to exhibit operating mode dependent loss behavior giving them potential for efficiency improvement in applications with a dominant operating mode such as electric vehicle traction, aerospace propulsion fans, and generators. For the first time, the conductor shaping method and associated benefits are demonstrated by the retrospective design, additive manufacture, and experimental test of a three-phase set of shaped profile windings for a concentrated wound, open slot, permanent magnet electrical machine.

[1]  S. Hodgson,et al.  Ceramic / inorganic-organic nano-hybrid composites for thermally stable insulation of electrical wires. Part I: Composition and synthetic parameters , 2020, IEEE Transactions on Dielectrics and Electrical Insulation.

[2]  Yacine Amara,et al.  Analytical Prediction of Eddy-Current Loss in Armature Windings of Permanent Magnet Brushless AC Machines , 2010, IEEE Transactions on Magnetics.

[3]  Jagadeesh Tangudu,et al.  Design Analysis of High Power Density Additively Manufactured Induction Motor , 2016 .

[4]  P. H. Mellor,et al.  Additive Manufacturing of Shaped Profile Windings for Minimal AC Loss in Electrical Machines , 2018, 2018 IEEE Energy Conversion Congress and Exposition (ECCE).

[5]  G. Slemon.  Magnetoelectric Devices: Transducers, Transformers and Machines , 1966 .

[6]  Phil Mellor,et al.  Design of High Performance Shaped Profile Windings for Additive Manufacture , 2019, 2019 IEEE Energy Conversion Congress and Exposition (ECCE).

[7]  Jagadeesh Tangudu,et al.  Topology Optimized End Winding for Additively Manufactured Induction Motor with Distributed Winding , 2016 .

[8]  Applied Electromagnetism , 2021, 2021 IEEE 26th International Seminar/Workshop on Direct and Inverse Problems of Electromagnetic and Acoustic Wave Theory (DIPED).

[9]  Phil H. Mellor,et al.  Additive manufacturing of shaped profile windings for minimal AC loss in gapped inductors , 2017, 2017 IEEE International Electric Machines and Drives Conference (IEMDC).

[10]  I.W. Hofsajer,et al.  Novel Technique for Shaped Planar Inductor Winding Optimization in Gapped Core Applications , 2007, 2007 IEEE Power Engineering Society Conference and Exposition in Africa - PowerAfrica.

[11]  STRAND CROSS-SECTION FOR HIGH FILL-FACTOR ELECTRIC MACHINE WINDINGS , 2017 .

[12]  Rafal Wrobel,et al.  Design of a Brushless PM Starter Generator for Low-Cost Manufacture and a High-Aspect-Ratio Mechanical Space Envelope , 2015, IEEE Transactions on Industry Applications.

[13]  M. J. Islam,et al.  Loss Reduction in a Salient Pole Synchronous Machine Due to Magnetic Slot Wedge and Semiclosed Stator Slots , 2018, 2018 XIII International Conference on Electrical Machines (ICEM).

[14]  Bernd Ponick,et al.  Design and direct liquid cooling of tooth-coil windings , 2018, Electrical Engineering.

[15]  Ming-Chuan Leu,et al.  Additive manufacturing: technology, applications and research needs , 2013, Frontiers of Mechanical Engineering.

[16]  Ankit Dalal,et al.  Analytical Model for Permanent Magnet Motor With Slotting Effect, Armature Reaction, and Ferromagnetic Material Property , 2015, IEEE Transactions on Magnetics.

[17]  C. Sullivan,et al.  Loss models for shaped foil windings on low-permeability cores , 2008, 2008 IEEE Power Electronics Specialists Conference.

[18]  Phil Mellor,et al.  AC losses in high frequency electrical machine windings formed from large section conductors , 2014, 2014 IEEE Energy Conversion Congress and Exposition (ECCE).

[19]  Rafal Wrobel,et al.  Test characterization of a high performance fault tolerant permanenet magnet machine , 2017, 2017 IEEE International Electric Machines and Drives Conference (IEMDC).

[20]  K. R. Williams,et al.  Etch rates for micromachining processing-Part II , 2003 .

[21]  Ayman M. El-Refaie,et al.  Fractional-Slot Concentrated-Windings Synchronous Permanent Magnet Machines: Opportunities and Challenges , 2010, IEEE Transactions on Industrial Electronics.

[22]  Fabian Lorenz,et al.  High Temperature Operation and Increased Cooling Capabilities of Switched Reluctance Machines using 3D Printed Ceramic Insulated Coils , 2018, 2018 IEEE Transportation Electrification Conference and Expo (ITEC).

[23]  Z. J. Cendes,et al.  Laminated steel eddy-current loss versus frequency computed using finite elements , 2000 .

[24]  Luca Papini,et al.  Fault Tolerant Design of Fractional Slot Winding Permanent Magnet Aerospace Actuator , 2016, IEEE Transactions on Transportation Electrification.

[25]  S. Ramakrishna,et al.  3D Printing of Highly Pure Copper , 2019, Metals.

[26]  Charles R. Sullivan,et al.  Computationally efficient winding loss calculation with multiple windings, arbitrary waveforms, and two-dimensional or three-dimensional field geometry , 2001 .

[27]  Ian A. Ashcroft,et al.  Electrical resistivity of additively manufactured AlSi10Mg for use in electric motors , 2018 .

[28]  C. Sadarangani,et al.  Winding factors and Joule losses of permanent magnet machines with concentrated windings , 2003, IEEE International Electric Machines and Drives Conference, 2003. IEMDC'03..

[29]  Haifeng Lu,et al.  Analytical model for armature reaction of outer rotor brushless permanent magnet DC motor , 2018 .