Self-Bearing Control of a Switched Reluctance Motor Using Sinusoidal Currents

Due to its special structure, the shaft radial force and torque of a switched reluctance motor can be separately controlled when all of the pole currents are independently controlled. In this paper, a control scheme for self-bearing operation of a 12/8 pole SRM drive is proposed. The rotor needs only one bearing for rotation and constraining the axial movement. The other end can move freely in the radial direction but is balanced with the radial force produced by the motor. A model for torque and radial force is derived and used to design the controller. Mutual inductance between the stator poles is included in the analysis to improve the model accuracy. The conduction phase pole currents are energized with phase-shifted sinusoidal currents. Depending on the requested radial force and torque, a descending-inductance phase may also be energized to increase radial force production. The requested force and torque are synthesized from the force and torque produced by these phases. The experimental results demonstrate successful SRM self-bearing operations. The rotor can be effectively balanced to the center of the air gap. The maximum radial position error was about 0.07 mm when the motor was rotating at 1500 r/min under full load torque.

[1]  T. Fukao,et al.  A method of determining advanced angle of square-wave currents in bearingless switched reluctance motors , 2000, Conference Record of the 2000 IEEE Industry Applications Conference. Thirty-Fifth IAS Annual Meeting and World Conference on Industrial Applications of Electrical Energy (Cat. No.00CH37129).

[2]  Iqbal Husain,et al.  Unbalanced force calculation in switched-reluctance machines , 2000 .

[3]  Sheng-Ming Yang,et al.  Instantaneous shaft radial force control with sinusoidal excitations for switched reluctance motors , 2007, Conference Record of the 2004 IEEE Industry Applications Conference, 2004. 39th IAS Annual Meeting..

[4]  R.D. Lorenz,et al.  Rotating vector methods for sensorless, smooth torque control of a switched reluctance motor drive , 1998, Conference Record of 1998 IEEE Industry Applications Conference. Thirty-Third IAS Annual Meeting (Cat. No.98CH36242).

[5]  Sheng-Ming Yang,et al.  Modeling and Control of Radial Force in Switched Reluctance Motor , 2006 .

[6]  David G. Dorrell,et al.  Magnetic Bearings and Bearingless Drives , 2005 .

[7]  H. Akagi,et al.  Radial force and torque of a bearingless switched reluctance motor operating in a region of magnetic saturation , 2002, Conference Record of the 2002 IEEE Industry Applications Conference. 37th IAS Annual Meeting (Cat. No.02CH37344).

[8]  Mohamed Gabsi,et al.  Effects of the airgap eccentricity on the SRM vibrations , 1999, IEEE International Electric Machines and Drives Conference. IEMDC'99. Proceedings (Cat. No.99EX272).

[9]  Akira Chiba,et al.  Improved analysis of a bearingless switched reluctance motor , 2001 .

[10]  Robert D. Lorenz,et al.  Rotating vector methods for smooth torque control of a switched reluctance motor drive , 2000 .

[11]  J. Wu,et al.  Decoupling Control of Radial Force in Bearingless Switched Reluctance Motors Based on Inverse System , 2006, 2006 6th World Congress on Intelligent Control and Automation.

[12]  T. Fukao,et al.  A decoupling control method of reluctance type bearingless motors considering magnetic saturation , 1995, IAS '95. Conference Record of the 1995 IEEE Industry Applications Conference Thirtieth IAS Annual Meeting.

[13]  Sheng-Ming Yang,et al.  Modeling and control of a self-bearing switched reluctance motor , 2005, Fourtieth IAS Annual Meeting. Conference Record of the 2005 Industry Applications Conference, 2005..

[14]  Tian-Hua Liu,et al.  Vector control and reliability improvement for a switched reluctance motor , 1994, Proceedings of 1994 IEEE International Conference on Industrial Technology - ICIT '94.