Effect of incorporating graphene oxide and surface imprinting on polysulfone membranes on flux, hydrophilicity and rejection of salt and polycyclic aromatic hydrocarbons from water

We report a significant enhancement of hydrophillity of polysulfone (Psf) membranes after modification with graphene oxide (GO) as a filler followed by surface imprinting on the surface of GO/Psf composite imprinted membranes (CIMs). The surface imprinting on the GO-Psf membrane was employed in order to enhance Its selectivity towards polycyclic aromatic hydrocarbons (PAHs) in water. The CIMs were prepared through a process of phase inversion of a mixture of graphene oxide and polysulfone (Psf) in N-ethylpyrrolidone (NMP). Fourier-transform spectroscopy (FT-IR) of the imprinted showed new peaks at 935 cm(-1) and 1638 cm(-1) indicating success in surface imprinting on the GO-Psf membrane. The CIM also showed improvement in flux from 8.56 LM-2 h(-1) of unmodified polysulfone membrane to 15.3 LM-2 h(-1) in the CIM, salt rejection increased from 57.2 +/- 4.2% of polysulfone membrane to 76 +/- %. The results obtained from the contact angle measurements showed a decrease with increase in GO content from 72 +/- 2.7% of neat polysulfone membrane to 62.3 +/- 2.1% of CIM indicating an improvement in surface hydrophilicity. The results from this study shows that, it is possible to improve the hydrophilicity of the membranes without affecting the performance of the membranes. (C) 2017 Elsevier Ltd. All rights reserved.

[1]  Ahmad Fauzi Ismail,et al.  Enhanced hydrophilicity and salt rejection study of graphene oxide-polysulfone mixed matrix membrane , 2013 .

[2]  Eun-sik Kim,et al.  Fabrication of porous polymeric nanocomposite membranes with enhanced anti-fouling properties: Effect of casting composition , 2013 .

[3]  T. Matsuura,et al.  Development of antifouling thin-film-composite membranes for seawater desalination , 2011 .

[4]  M. Nieuwenhuijsen,et al.  Assessing the human health impacts of exposure to disinfection by-products--a critical review of concepts and methods. , 2015, Environment international.

[5]  Jun Ma,et al.  Surface modification of UF membranes with functionalized MWCNTs to control membrane fouling by NOM fractions , 2015 .

[6]  C. Kiparissides,et al.  Synthesis of Novel Composite Membranes Based on Molecularly Imprinted Polymers for Removal of Triazine Herbicides from Water , 2013 .

[7]  S. Khondaker,et al.  Graphene based materials: Past, present and future , 2011 .

[8]  John O'Mahony,et al.  Molecular imprinting science and technology: a survey of the literature for the years up to and including 2003 , 2006, Journal of molecular recognition : JMR.

[9]  Guo-Rong Xu,et al.  Strategies for improving the performance of the polyamide thin film composite (PA-TFC) reverse osmosis (RO) membranes: Surface modifications and nanoparticles incorporations , 2013 .

[10]  S. Nguyen,et al.  Graphene oxide, highly reduced graphene oxide, and graphene: versatile building blocks for carbon-based materials. , 2010, Small.

[11]  Masoud Rahimi,et al.  Preparation of a novel antifouling mixed matrix PES membrane by embedding graphene oxide nanoplates , 2014 .

[12]  B. Mamba,et al.  Synthesis and application of reduced graphene oxide and molecularly imprinted polymers composite in chemo sensor for trichloroacetic acid detection in aqueous solution , 2014 .

[13]  Ashutosh Kumar Singh,et al.  Review of Endocrine-Disrupting-Compound Removal Technologies in Water and Wastewater Treatment Plants: An EU Perspective , 2011 .

[14]  Heechul Choi,et al.  Carbon nanotube blended polyethersulfone membranes for fouling control in water treatment. , 2011, Water research.

[15]  H. Ng,et al.  Fabrication of mesh-embedded double-skinned substrate membrane and enhancement of its surface hydrophilicity to improve anti-fouling performance of resultant thin-film composite forward osmosis membrane , 2016 .

[16]  Jian Yan,et al.  Photomutagenicity of 16 polycyclic aromatic hydrocarbons from the US EPA priority pollutant list. , 2004, Mutation research.

[17]  Guodong Kang,et al.  Development of antifouling reverse osmosis membranes for water treatment: A review. , 2012, Water research.

[18]  A. El'skaya,et al.  Porous molecularly imprinted polymer membranes and polymeric particles. , 2007, Analytica chimica acta.

[19]  Yongsheng Yan,et al.  A novel approach toward fabrication of porous molecularly imprinted nanocomposites with bioinspired multilevel internal domains: Application to selective adsorption and separation membrane , 2016 .

[20]  Jeong F. Kim,et al.  Molecularly imprinted organic solvent nanofiltration membranes -Revealing molecular recognition and solute rejection behaviour , 2015 .

[21]  A. Isloor,et al.  Preparation and characterization of polysulfone and modified poly isobutylene-alt-maleic anhydride blend NF membrane , 2012 .

[22]  M. Ioniță,et al.  Improving the thermal and mechanical properties of polysulfone by incorporation of graphene oxide , 2014 .

[23]  Zhen-liang Xu,et al.  Molecularly imprinted membranes for the recognition of lovastatin acid in aqueous medium by a template analogue imprinting strategy , 2008 .

[24]  R. J. Krupadam,et al.  Removal of probable human carcinogenic polycyclic aromatic hydrocarbons from contaminated water using molecularly imprinted polymer. , 2010, Water research.

[25]  M. Ulbricht.  Membrane separations using molecularly imprinted polymers. , 2004, Journal of chromatography. B, Analytical technologies in the biomedical and life sciences.

[26]  I. Ortiz,et al.  Recent progress in development of high performance polymeric membranes and materials for metal plating wastewater treatment: A review , 2016 .

[27]  M. Jaffrin,et al.  A Review on Flux Decline Control Strategies in Pressure-Driven Membrane Processes , 2015 .

[28]  N. Hilal,et al.  Selective recognition of organic pollutants in aqueous solutions with composite imprinted membranes. , 2010, Advances in colloid and interface science.