Design, modeling, and fabrication of crab-shape capacitive microphone using silicon-on-isolator wafer

Abstract. This paper presents design, modeling, and fabrication of a crab-shape microphone using silicon-on-isolator (SOI) wafer. SOI wafer is used to prevent the additional deposition of sacrificial and diaphragm layers. The holes have been made on diaphragm to prevent back plate etching. Dry etching is used for removing the sacrificial layer, because wet etching causes adhesion between the diaphragm and the back plate. Crab legs around the perforated diaphragm allow for improving the microphone performance and reducing the mechanical stiffness and air damping of the microphone. In this structure, the supply voltage is decreased due to the uniform deflection of the diaphragm due to the designed low-K (spring constant) structure. An analytical model of the structure for description of microphone behavior is presented. The proposed method for estimating the basic parameters of the microphone is based on the calculation of the spring constant using the energy method. The microphone is fabricated using only one mask to pattern the crab-shape diaphragm, resulting in a low-cost and easy fabrication process. The diaphragm size is 0.3  mm×0.3  mm, which is smaller than the conventional microelectromechanical systems capacitive microphone. The results show that the analytical equations have a good agreement with measurement results. The device has the pull-in voltage of 14.3 V, a resonant frequency of 90 kHz, an open-circuit sensitivity of 1.33  mV/Pa under bias voltage of 5 V. Comparing with previous works, this microphone has several advantages: SOI wafer decreases the fabrication process steps, the microphone is smaller than the previous works, and crab-shape diaphragm improves the microphone performances.

[1]  Rongming Lin,et al.  Modeling and characterization of a silicon condenser microphone , 2004 .

[2]  Bahram Azizollah Ganji,et al.  Application of He’s variational iteration method to the estimation of diaphragm deflection in MEMS capacitive microphone , 2011 .

[3]  Reza Ansari,et al.  Design and modeling of a frog-shape MEMS capacitive microphone using SOI technology , 2018 .

[4]  Hannu Sipola,et al.  Capacitive microphone with low-stress polysilicon membrane and high-stress polysilicon backplate , 2000 .

[5]  Ryutaro Maeda,et al.  Ten-Micrometer-Thick Silicon Diaphragm Used in Condenser Microphone , 2013 .

[6]  Gisela Hess,et al.  A subminiature condenser microphone with silicon nitride membrane and silicon back plate , 1989 .

[7]  Alfons Dehe,et al.  Silicon microphone development and application , 2007 .

[8]  Burhanuddin Yeop Majlis,et al.  Design and fabrication of a new MEMS capacitive microphone using a perforated aluminum diaphragm , 2009 .

[9]  Mingyi Wang,et al.  Implementation of the CMOS MEMS Condenser Microphone with Corrugated Metal Diaphragm and Silicon Back-Plate , 2011, Sensors.

[10]  W. Kronast,et al.  Single-chip condenser microphone using porous silicon as sacrificial layer for the air gap , 1998, Proceedings MEMS 98. IEEE. Eleventh Annual International Workshop on Micro Electro Mechanical Systems. An Investigation of Micro Structures, Sensors, Actuators, Machines and Systems (Cat. No.98CH36176.

[11]  Masakazu Iwaki,et al.  Silicon microphone with wide frequency range and high linearity , 2007 .

[12]  Suan Hee Seah,et al.  Design considerations in micromachined silicon microphones , 2002 .

[13]  Kensall D. Wise,et al.  A high sensitivity polysilicon diaphragm condenser microphone , 1998, Proceedings MEMS 98. IEEE. Eleventh Annual International Workshop on Micro Electro Mechanical Systems. An Investigation of Micro Structures, Sensors, Actuators, Machines and Systems (Cat. No.98CH36176.

[14]  Chang Han Je,et al.  The Novel Sensitivity Improved Surface Micromachined MEMS Microphone with the Center-Hole Membrane , 2011 .

[15]  Smieee,et al.  High sensitivity and small size MEMS capacitive microphone using a novel slotted diaphragm , 2009 .

[16]  T. Brosnihan,et al.  A MEMS Condenser Microphone for Consumer Applications , 2006, 19th IEEE International Conference on Micro Electro Mechanical Systems.