Modelling of adequate pretwist for obtaining straight timber

Abstract Wood in general and wooden studs in particular are often distorted owing to uneven shrinkage during the drying process in the sawmill. Twist is often the most detrimental of all types of distortion, and it is caused by spiral grain in combination with variations in moisture content. For sawmills, the objective is to produce dried, straight boards, and one method of dealing with boards with excessive spiral grain is to sort them out and then dry them in a pretwisted position to obtain straight boards after drying. A model using the finite element (FE) method for the simulation of drying twist distortions was first calibrated against laboratory experiments in which boards were dried with and without restraints and pretwists. After the calibration, the FE results were compared with industrial test results for boards that were dried without restraints or with restraints with zero pretwist, i.e. straight restraints. The FE model used an elastic–ideally plastic material model to obtain permanent deformations. The calibration was to set the yield stresses so that there was a good match between FE results and results from the laboratory experiments. The comparison between the industrial test results and the FE results showed that the FE model is capable of realistic simulations of drying boards with and without restraints and presumably also pretwists.

[1]  Sigurdur Ormarsson,et al.  Numerical Analysis of Moisture-Related Distortion in Sawn Timber , 1999 .

[2]  P. Audebert,et al.  Modeling and smiulation of (visco)-plastic behavior of wood under moisture change , 1999 .

[3]  Mats Ekevad,et al.  Local water vapor diffusion coefficient when drying Norway spruce sapwood , 2005, Journal of Wood Science.

[4]  Numerical analysis of drying induced stresses in timber: An orthotropic model , 1983 .

[5]  Stephen W. Tsai,et al.  A General Theory of Strength for Anisotropic Materials , 1971 .

[6]  Steven J. DeTeresa,et al.  Reduction in the Number of Independent Parameters for the Tsai—Wu Tensor Polynomial Theory of Strength for Composite Materials , 2003 .

[7]  M. Ekevad.  Twist of wood studs: dependence on spiral grain gradient , 2005, Journal of Wood Science.

[8]  Harald Säll,et al.  Spiral Grain in Norway Spruce , 2002 .

[9]  S. Pang.  External Heat and Mass Transfer Coefficients for Kiln Drying of Timber , 1996 .

[10]  Staffan Svensson,et al.  Stress-Strain Relationship of Drying Wood. Part 1: Development of a Constitutive Model , 1997 .

[11]  W. C. Stevens,et al.  Distortion caused by spiralled grain. , 1960 .

[12]  R. Kliger,et al.  Influence of Material Characteristics on Warp In Norway Spruce Studs , 2007 .

[13]  S. Skatter,et al.  The cause of the prevalent directions of the spiral grain patterns in conifers , 1998, Trees.

[14]  Frank Lam,et al.  Computational modeling of strand-based wood composites , 2001 .

[15]  Marie Johansson,et al.  Distortion of Norway spruce timber Part 2. Modelling twist , 2001, Holz als Roh- und Werkstoff.

[16]  Micael Öhman,et al.  The measurement of compression wood and other wood features and the prediction of their impact on wood products , 2001 .

[17]  Mikael Perstorper,et al.  Quality of Structural Timber - End-User Requirements and Performance Control , 1994 .

[18]  J. Salin.  Drying of boards, prone to twist, in a pre-twisted position. , 2005 .

[19]  G. Johansson,et al.  Quality of structural timber-product specification system required by end-users , 1994, Holz als Roh- und Werkstoff.

[20]  H. Mang,et al.  Rate-independent mechanical behavior of biaxially stressed wood: Experimental observations and constitutive modeling as an orthotropic two-surface elasto-plastic material , 2005 .

[21]  Steven R. Shook,et al.  Material substitution in the U.S. residential construction industry, 1994 versus 1998 , 2001 .

[22]  H. Vermaas,et al.  Steaming under Restraint to Remove Twist in Previously Dried Pinus radiata Boards , 1988 .

[23]  Frede Danborg,et al.  Drying properties and visual grading of juvenile wood from fast grown Picea abies and Picea sitchensis , 1994 .