Low-cycle fatigue small crack initiation and propagation behaviour of cast magnesium alloys based on in-situ SEM observations

In-situ observations on the initiation and propagation behaviour of low-cycle fatigue small cracks in cast magnesium–aluminium alloys (AM50 and AM60B) were carried out with scanning electron microscopy (SEM) to elucidate the resistance to fatigue cracking and to evaluate the fatigue small crack growth rate accurately and quantitatively. The results indicate that the fatigue small cracks formed preferentially on β-phase (Mg17Al12) boundaries at room temperature. In addition, the effects of the parameters of stress levels in low-cycle fatigue and temperatures as well as microstructure on fatigue small crack propagation behaviour are revealed. The variation of crack open displacement (COD) with stress levels and cycles at elevated temperature shows that it is unsuitable to estimate the fatigue small crack growth rate of cast magnesium alloys using conventional measurement methods such as the plastic-replica technique due to the obvious difference between microscopic cracks in the open and closed states. Stabilized crack propagation behaviour is limited to cases where the physical crack length is less than 1 mm in low-cycle fatigue.

[1]  K. Miller.  THE SHORT CRACK PROBLEM , 1982 .

[2]  R. W. Landgraf,et al.  Advances in Fatigue Lifetime Predictive Techniques , 1992 .

[3]  G. Socha.  Experimental investigations of fatigue cracks nucleation, growth and coalescence in structural steel , 2003 .

[4]  A. K. Dahle,et al.  Development of the as-cast microstructure in magnesium-aluminium alloys , 2001 .

[5]  J. C. Newman,et al.  Small-Crack Effects in High-Strength Aluminum Alloys A NASA/CAE Cooperative Program , 1994 .

[6]  Xi-Qiao Feng,et al.  Failure Behavior of Anodized Coating-Magnesium Alloy Substrate Structures , 2004 .

[7]  S. Nam,et al.  Effects of Mn-dispersoids on the fatigue mechanism in an Al–Zn–Mg alloy , 1998 .

[8]  D. Nelson,et al.  A study of small crack growth in aluminum alloy 7075-T6 , 2002 .

[9]  M. Goto,et al.  Application of Small Crack Growth Law to Different Types of Loading. , 1997 .

[10]  Xi-Shu Wang,et al.  Investigation of surface fatigue microcrack growth behavior of cast Mg–Al alloy , 2004 .

[11]  D. Eliezer,et al.  Environmental Behavior of Magnesium and Magnesium Alloysd , 2001 .

[12]  Arno Jambor,et al.  New cars — new materials , 1997 .

[13]  Henrik Andersson,et al.  In-situ SEM study of fatigue crack growth behaviour in IN718 , 2004 .

[14]  Xi-Shu Wang,et al.  Direct Observation of Fatigue Cracking in the Fuel Plate Using the Scanning Electron Microscope , 2004 .

[15]  Xi-Shu Wang,et al.  Experiments, characterizations and analysis of a U3Si2-Al dispersion fuel plate with sandwich structure , 2004 .

[16]  G. G. Stokes.  "J." , 1890, The New Yale Book of Quotations.

[17]  K. Tokaji,et al.  Fatigue behaviour and fracture mechanism of a rolled AZ31 magnesium alloy , 2004 .

[18]  J. Newman,et al.  Mechanics of Fatigue Crack Closure , 1988 .

[19]  Nisitani Hironobu,et al.  A small-crack growth law and its related phenomena , 1992 .

[20]  T. Miyata,et al.  The effect of microstructure on fatigue crack propagation of α + β titanium alloys in-situ observation of short fatigue crack growth , 1998 .

[21]  J. Polák,et al.  FATIGUE DAMAGE IN TWO‐STEP LOADING OF 316L STEEL II. SHORT CRACK GROWTH , 1996 .

[22]  O. Kolednik.  The yield stress gradient effect in inhomogeneous materials , 2000 .

[23]  J. Donald,et al.  A Procedure for Standardizing Crack Closure Levels , 1988 .

[24]  Xi-Shu Wang,et al.  An evaluation on the growth rate of small fatigue cracks in cast AM50 magnesium alloy at different temperatures in vacuum conditions , 2006 .

[25]  David L. McDowell,et al.  In-situ observations of high cycle fatigue mechanisms in cast AM60B magnesium in vacuum and water vapor environments , 2004 .

[26]  Shuang-shou Li,et al.  An investigation on hot-crack mechanism of Ca addition into AZ91D alloy , 2005 .

[27]  Xi-Shu Wang,et al.  SEM online investigation of fatigue crack initiation and propagation in cast magnesium alloy , 2004 .

[28]  K. J. Miller,et al.  What is fatigue damage? A view point from the observation of low cycle fatigue process , 2005 .

[29]  W. Soboyejo,et al.  An investigation of the effects of stress ratio and crack closure on the micromechanisms of fatigue crack growth in Ti-6Al-4V , 1997 .

[30]  Ding,et al.  Small‐crack growth and fatigue life predictions for high‐strength aluminium alloys. Part II: crack closure and fatigue analyses , 2000 .

[31]  P. Bowen,et al.  CRACK CLOSURE IN SMALL FATIGUE CRACKS—A COMPARISON OF FINITE ELEMENT PREDICTIONS WITH IN‐SITU SCANNING ELECTRON MICROSCOPE MEASUREMENTS , 1997 .

[32]  David L. McDowell,et al.  An engineering model for propagation of small cracks in fatigue , 1997 .

[33]  Wei Li,et al.  Investigation of initiation and growth behavior of short fatigue cracks emanating from a single edge notch specimen using in-situ SEM , 2001 .

[34]  Shuang-shou Li,et al.  Effects of Ca combined with Sr additions on microstructure and mechanical properties of AZ91D magnesium alloy , 2005 .

[35]  Stefanie E. Stanzl-Tschegg,et al.  Fatigue and fatigue crack growth of aluminium alloys at very high numbers of cycles , 2001 .

[36]  S. Pearson.  Initiation of fatigue cracks in commercial aluminium alloys and the subsequent propagation of very short cracks , 1975 .