Meso scale MEMS inertial switch fabricated using an electroplated metal-on-insulator process

In this work, we report on a novel simple yet robust two-mask metal-on-insulator (MOI) process and illustrate its implementation for the fabrication of a meso scale MEMS inertial switch. The devices were fabricated of a ?40??m thick layer of nickel electrodeposited on top of a 4??m thick thermal field oxide (TOX) covering a single crystal silicon wafer. A 40??m thick layer of KMPR??resist was used as a mold and allowed the formation of high-aspect-ratio (1:5) metal structures. The devices were released by the sacrificial etching of the TOX layer in hydrofluoric acid. The fabricated devices were mounted in a ceramic enclosure and were characterized using both an electromagnet shaker and a drop tester. The functionality of the switch, aimed to trigger an electrical circuit when subjected to an acceleration pulse with amplitude of 300 g and duration of 200??s, was demonstrated experimentally and the performance targets were achieved. The experimental results were consistent with the model predictions obtained through finite element simulations.

[1]  Tim South,et al.  Fundamentals of vibration , 2013 .

[2]  Zhihong Li,et al.  Bulk micromachined relay with lateral contact , 2000 .

[3]  R. Pratap,et al.  A Compact Squeeze-Film Model Including Inertia, Compressibility, and Rarefaction Effects for Perforated 3-D MEMS Structures , 2008, Journal of Microelectromechanical Systems.

[4]  Thangavelu Palaniselvam,et al.  Graphene based 2D-materials for supercapacitors , 2015 .

[5]  Michael Curt Elwenspoek,et al.  Comb-drive actuators for large displacements , 1996 .

[6]  J. Oberhammer,et al.  Mechanically tri-stable SPDT metal-contact MEMS switch embedded in 3D transmission line , 2007, 2007 European Microwave Conference.

[7]  U. Sonmez.  Compliant MEMS Crash Sensor Designs: The Preliminary Simulation Results , 2007, 2007 IEEE Intelligent Vehicles Symposium.

[8]  Minhang Bao,et al.  Squeeze film air damping in MEMS , 2007 .

[9]  Hong Wang,et al.  Fabrication and characterization of a multidirectional-sensitive contact-enhanced inertial microswitch with a electrophoretic flexible composite fixed electrode , 2012 .

[10]  Guifu Ding,et al.  Design, simulation and characterization of an inertia micro-switch fabricated by non-silicon surface micromachining , 2007 .

[11]  Hong Wang,et al.  Design, simulation and fabrication of a novel contact-enhanced MEMS inertial switch with a movable contact point , 2008 .

[12]  Gang Li,et al.  Fabrication and packaging of inertia micro-switch using low-temperature photo-resist molded metal-electroplating technology , 2004 .

[13]  Zhenchuan Yang,et al.  An acceleration switch with a robust latching mechanism and cylindrical contacts , 2010 .

[14]  P. Zavracky,et al.  Measurement and modelling of surface micromachined, electrostatically actuated microswitches , 1997, Proceedings of International Solid State Sensors and Actuators Conference (Transducers '97).

[15]  Masayoshi Esashi,et al.  Acceleration switch with extended holding time using squeeze film effect for side airbag systems , 2002 .

[16]  J. J. Blech.  On Isothermal Squeeze Films , 1983 .

[17]  M. Esashi,et al.  Simple modeling and simulation of the squeeze film effect and transient response of the MEMS device , 1999, Technical Digest. IEEE International MEMS 99 Conference. Twelfth IEEE International Conference on Micro Electro Mechanical Systems (Cat. No.99CH36291).

[18]  Slava Krylov,et al.  Excitation of large-amplitude parametric resonance by the mechanical stiffness modulation of a microstructure , 2009 .

[19]  T Tønnesen,et al.  Simulation, design and fabrication of electroplated acceleration switches , 1997 .

[20]  Guifu Ding,et al.  Fabrication of a MEMS inertia switch on quartz substrate and evaluation of its threshold acceleration , 2008, Microelectron. J..

[21]  Tayfun Akin,et al.  A low-cost rate-grade nickel microgyroscope , 2006 .

[22]  Kun Lian,et al.  Design and fabrication of a SU-8 based electrostatic microactuator , 2006 .

[23]  Josef Binder,et al.  Additive electroplating technology as a post-CMOS process for the production of MEMS acceleration-threshold switches for transportation applications , 2000 .

[24]  G. J. M. Krijnen,et al.  Temporally Aliased Video Microscopy: An Undersampling Method for In-Plane Modal Analysis of Microelectromechanical Systems , 2012, Journal of Microelectromechanical Systems.

[25]  Suhas S. Mohite,et al.  Squeeze Film Effects in MEMS Devices , 2007 .

[26]  Hong Wang,et al.  Development of a Novel MEMS Inertial Switch With a Compliant Stationary Electrode , 2009, IEEE Sensors Journal.

[27]  Ai Qun Liu,et al.  A single-pole double-throw (SPDT) circuit using lateral metal-contact micromachined switches , 2005 .

[28]  K. R. Williams,et al.  Etch rates for micromachining processing-Part II , 2003 .

[29]  Yuelin Wang,et al.  Micro-cantilever shocking-acceleration switches with threshold adjusting and 'on'-state latching functions , 2007 .

[30]  Yogesh B. Gianchandani,et al.  LIGA fabricated 19-element threshold accelerometer array , 2004 .