Physical and electrochemical properties of Nafion/polypyrrole composite membrane for DMFC

Abstract Nafion/polypyrrole composite membrane was prepared by chemical in situ polymerization for a direct methanol fuel cell. The composite membrane was characterized by quantitative analysis, DMA, TGA, EPMA, water and methanol uptake tests, conductivity and permeability measurements, and unit cell operation. The mechanical and thermal properties of the composite membrane were enhanced due to the interaction between the polar phase of Nafion and secondary ammonium groups of polypyrrole. In addition, the sorption properties of the composite membrane influenced two transport properties, proton conductivity and methanol crossover. The optimization of cell performance was related to the distribution of polypyrrole particles over the cross section of the membrane. In particular when the polypyrrole particles were mainly present near the surface rather than in the internal space, the difference in the relative proton conductivity and the relative methanol permeability was largest. It is supposed that the existence of the polypyrrole particles near the surface such as thin film was favorable to reducing methanol crossover with maintaining proton conductivity. As a result of that, N/P 003 had higher performance than Nafion under the specific condition.

[1]  Y. Kawano,et al.  Thermal Behavior of Nafion Membranes , 1999 .

[2]  M. Verbrugge.  Methanol Diffusion in Perfluorinated Ion‐Exchange Membranes , 1989 .

[3]  S. Woo,et al.  Evaluation of a palladinized Nafion™ for direct methanol fuel cell application , 2004 .

[4]  Shimshon Gottesfeld,et al.  Water and Methanol Uptakes in Nafion Membranes and Membrane Effects on Direct Methanol Cell Performance , 2000 .

[5]  Jung-Ki Park,et al.  Characteristics of PVdF copolymer/Nafion blend membrane for direct methanol fuel cell (DMFC) , 2004 .

[6]  P. Pickup,et al.  Characteristics of Polypyrrole/Nafion Composite Membranes in a Direct Methanol Fuel Cell , 2003 .

[7]  Robert B. Moore,et al.  Morphology and chemical properties of the Dow perfluorosulfonate ionomers , 1989 .

[8]  G. Alberti,et al.  Composite Membranes for Medium-Temperature PEM Fuel Cells , 2003 .

[9]  R. Savinell,et al.  A Polymer Electrolyte for Operation at Temperatures up to 200°C , 1994 .

[10]  Chang Chur-Min,et al.  Impedance analysis of the transport of counter ions at polypyrrole-Nafion composite electrodes , 1995 .

[11]  K. Mauritz,et al.  Microstructural evolution of a silicon oxide phase in a perfluorosulfonic acid ionomer by an in situ sol-gel reaction. 3. Thermal analysis studies , 1990 .

[12]  T. Sata.  Properties of ion-exchange membranes combined anisotropically with conducting polymers. 2. Relationship of electrical potential generation to preparation conditions of composite membranes , 1991 .

[13]  V. Tricoli.  Proton and Methanol Transport in Poly(perfluorosulfonate) Membranes Containing Cs + and H + Cations , 1998 .

[14]  P. Pickup,et al.  Partitioning and Polymerization of Pyrrole into Perfluorosulfonic Acid (Nafion) Membranes , 2003 .

[15]  Michael A. Hickner,et al.  State of Water in Disulfonated Poly(arylene ether sulfone) Copolymers and a Perfluorosulfonic Acid Copolymer (Nafion) and Its Effect on Physical and Electrochemical Properties , 2003 .

[16]  H. Yeager,et al.  Perfluorinated Ionomer Membranes , 1982 .

[17]  S. Woo,et al.  Proton conductivity and methanol permeation in Nafion™/ORMOSIL prepared with various organic silanes , 2004 .

[18]  H. Park,et al.  Influence of morphology on the transport properties of perfluorosulfonate ionomers/polypyrrole composite membrane , 2005 .

[19]  T. Kyu,et al.  Mechanical Relaxations in Perfluorosulfonate Ionomer Membranes , 1982 .

[20]  Tae-Hee Lee,et al.  Performance of polypyrrole-impregnated composite electrode for unitized regenerative fuel cell , 2004 .