Flank wear measurement by a threshold independent method with sub-pixel accuracy

This paper presents an image processing procedure to detect and measure the tool flank wear area. Unlike the traditional thresholding-based methods, a rough-to-fine strategy is considered in this paper whereby a binary image is first obtained and used to find the candidate wear bottom edge points; then a threshold-independent edge detection method based on moment invariance is employed for more robust determination of the wear edge with sub-pixel accuracy. To shorten computation time, a critical area is initially defined and the subsequent procedure is confined to processing this area as the region of interest. Images from three types of inserts, A30N, AC325 and ACZ350 under different cutting conditions are captured with the similar illumination conditions after milling. The measured results obtained with the proposed method from these images are compared with those obtained by direct manual measurement with a toolmaker's microscope and a method based totally on binary image contour detection. The proposed method is shown to be effective and suitable for the unmanned measurement of flank wear.

[1]  Tilo Pfeifer,et al.  Reliable tool wear monitoring by optimized image and illumination control in machine vision , 2000 .

[2]  Ju-Hyun Jeon,et al.  Optical flank wear monitoring of cutting tools by image processing , 1988 .

[3]  K. N. Prasad,et al.  Tool wear evaluation by stereo vision and prediction by artificial neural network , 2001 .

[4]  Kenneth W. Tobin,et al.  6 th International Conference on Quality Control by Artificial Vision , 2003 .

[5]  A. Galip Ulsoy,et al.  On-Line Flank Wear Estimation Using an Adaptive Observer and Computer Vision, Part 2: Experiment , 1993 .

[6]  S. M. Taboun,et al.  A machine vision system for wear monitoring and breakage detection of single-point cutting tools , 1994 .

[7]  G. Boothroyd,et al.  Fundamentals of Metal Machining and Machine Tools , 1975 .

[8]  Kjeld Bruno Pedersen,et al.  Wear measurement of cutting tools by computer vision , 1990 .

[9]  Min-Yang Yang,et al.  Crater wear measurement using computer vision and automatic focusing , 1996 .

[10]  N. Otsu.  A threshold selection method from gray level histograms , 1979 .

[11]  Michele Lanzetta,et al.  A new flexible high-resolution vision sensor for tool condition monitoring , 2001 .

[12]  Reinhard Klette,et al.  Handbook of image processing operators , 1996 .

[13]  Colin Bradley,et al.  A review of machine vision sensors for tool condition monitoring , 1997 .

[14]  Santanu Das,et al.  3D tool wear measurement and visualisation using stereo imaging , 1997 .

[15]  Colin Bradley,et al.  A machine vision system for tool wear assessment , 1997 .

[16]  F Giusti,et al.  On-Line Sensing of Flank and Crater Wear of Cutting Tools , 1987 .

[17]  A. Yamamoto,et al.  Contour mapping of cutting tool face with the aid of digital image processing technique , 1987 .

[18]  Young Shik Moon,et al.  An efficient method of estimating edge locations with subpixel accuracy in noisy images , 1999, Proceedings of IEEE. IEEE Region 10 Conference. TENCON 99. 'Multimedia Technology for Asia-Pacific Information Infrastructure' (Cat. No.99CH37030).

[19]  Kazuaki Iwata,et al.  Estimation of Cutting Tool Life by Processing Tool Image Data with Neural Network , 1993 .

[20]  Elisabetta Ceretti,et al.  A Neural Network Architecture for Tool Wear Detection through Digital Camera Observations , 1996 .

[21]  A. Galip Ulsoy,et al.  On-Line Flank Wear Estimation Using an Adaptive Observer and Computer Vision, Part 1: Theory , 1993 .

[22]  Y. Maeda,et al.  Estimation of wear land width of cutting tool flank with the aid of digital image processing technique , 1987 .