Gear transmission rattle: Assessment of meshing forces under hydrodynamic lubrication

This work has been supported by project DPI2013-44860 funded by the Spanish Ministry of Science and Technology and project PRX14/00451 funded by the Spanish Ministry of Education, Culture and Sports and COST Action TU 1105.

[1]  Ramon Sancibrian,et al.  Gear transmission dynamic: Effects of tooth profile deviations and support flexibility , 2014 .

[2]  Cheon Gill-Jeong,et al.  Analysis of the nonlinear behavior of gear pairs considering hydrodynamic lubrication and sliding friction , 2009 .

[3]  Homer Rahnejat,et al.  Gear teeth impacts in hydrodynamic conjunctions promoting idle gear rattle , 2007 .

[4]  Raynald Guilbault,et al.  Nonlinear damping calculation in cylindrical gear dynamic modeling , 2012 .

[5]  Colin Richard Evans.  Measurement and mapping of the rheological properties of elastohydrodynamic lubricants , 1984 .

[6]  Mohamed Haddar,et al.  Axle gear oils: Tribological characterization under full film lubrication , 2017 .

[7]  Ramiro C. Martins,et al.  Efficiency of a gearbox lubricated with wind turbine gear oils , 2014 .

[8]  D. M. McFarland,et al.  Analytical characterization of damping in gear teeth dynamics under hydrodynamic conditions , 2015 .

[9]  A. Diez-Ibarbia,et al.  Gear transmission dynamics: Effects of index and run out errors , 2016 .

[10]  Homer Rahnejat,et al.  Prediction of airborne radiated noise from lightly loaded lubricated meshing gear teeth , 2015 .

[11]  P. Velex,et al.  Modelling of damping in lubricated line contacts – Applications to spur gear dynamic simulations , 2016 .

[12]  W.W.F. Chong,et al.  Elastoplastic contact of rough surfaces: a line contact model for boundary regime of lubrication , 2014 .

[13]  Sheng Li,et al.  A tribo-dynamic model of a spur gear pair , 2013 .

[14]  James R. Ottewill,et al.  An investigation into the effect of tooth profile errors on gear rattle , 2010 .

[15]  A. Diez-Ibarbia,et al.  Efficiency analysis of spur gears with a shifting profile , 2016 .

[16]  Emiliano Mucchi,et al.  Modelling dynamic behaviour and noise generation in gear pumps: Procedure and validation , 2014 .

[17]  Riccardo Russo,et al.  Experimental investigations about the influence of oil lubricant between teeth on the gear rattle phenomenon , 2009 .

[18]  Homer Rahnejat,et al.  Transient mixed thermo-elastohydrodynamic lubrication in multi-speed transmissions , 2012 .

[19]  A. Diez-Ibarbia,et al.  Advanced model for the calculation of meshing forces in spur gear planetary transmissions , 2015 .

[20]  Emiliano Mucchi,et al.  Elasto-dynamic analysis of a gear pump-Part IV: Improvement in the pressure distribution modelling , 2015 .

[21]  Mohamed Haddar,et al.  Analysis of planetary gear transmission in non-stationary operations , 2013 .

[22]  A. Fernandez del Rincon,et al.  A model for the study of meshing stiffness in spur gear transmissions , 2013 .

[23]  Ernesto Rocca,et al.  An analysis of the automotive driveline dynamic behaviour focusing on the influence of the oil squeeze effect on the idle rattle phenomenon , 2007 .

[24]  Homer Rahnejat,et al.  The Vibrations of Radial Ball Bearings , 1985 .

[25]  Paulo Flores.  Kinematics and Dynamics of Mechanical Systems with Lubricated Revolute Joints: the Infinitely-Short Journal-Bearing Approach , 2015 .

[26]  Aki Mikkola,et al.  Planetary gear sets power loss modeling: Application to wind turbines , 2017 .