Study of metal adhesion on porous low-k dielectric using telephone cord buckling

Abstract The interfacial adhesion energy between metal and porous low-k dielectrics is an important parameter for the reliability study of back-end of line integration. In this work, we have observed the spontaneous film delamination with telephone cord morphology after 130 nm thick Ta was sputtered onto methyl silsesquioxane (MSQ) low-k dielectric. The highly compressive stress inside the Ta film is the driving force for the spontaneous buckling. The adhesion failure was identified to be at Ta/MSQ interface by using focused ion beam and scanning electron microscopy. Pinned circular blister model was applied to fit the buckling morphology. The interfacial adhesion energy was extracted to be 7.90 J/m2 at 87° phase angle. The Cu/MSQ interface was evaluated in a similar fashion by using a stressed overlayer Ta/Cu. The fracture energy was calculated to be 3.34 J/m2 with the similar phase angle. The results suggest that an adhesion promoter between Cu and low-k dielectrics is essential for a mechanically stable structure.

[1]  Barrier Layer Morphological Stability and Adhesion to Porous LOW-κ Dielectrics , 2004 .

[2]  Daniel C. Edelstein,et al.  Copper Metallization for High Performance Silicon Technology , 2000 .

[3]  Karen Maex,et al.  Low dielectric constant materials for microelectronics , 2003 .

[4]  M. Ohring.  The Materials Science of Thin Films , 1991 .

[5]  Toh-Ming Lu,et al.  Kinetics of Ta ions penetration into porous low-k dielectrics under bias-temperature stress , 2010 .

[6]  N. Moody,et al.  Recent developments in thin film adhesion measurement , 2004, IEEE Transactions on Device and Materials Reliability.

[7]  S. Murarka,et al.  Metal drift behavior in low dielectric constant organosiloxane polymer , 2001 .

[8]  A. Volinsky,et al.  Fracture toughness, adhesion and mechanical properties of low-K dielectric thin films measured by nanoindentation , 2003 .

[9]  J. Vella,et al.  Mechanical properties and fracture toughness of organo-silicate glass (OSG) low-k dielectric thin films for microelectronic applications , 2003 .

[10]  Anthony G. Evans,et al.  The characterization of telephone cord buckling of compressed thin films on substrates , 2002 .

[11]  David F. Bahr,et al.  Adhesion measurements using telephone cord buckles , 2007 .

[12]  Alex A. Volinsky,et al.  Interfacial toughness measurements for thin films on substrates , 2002 .

[13]  S. P. Murarka,et al.  Metallization: Theory and practice for VLSI and ULSI , 1992 .

[14]  M. Lane,et al.  Effect of Nitrogen Content on Interfacial Adhesion of the Ta/SiO 2 Interface , 1999 .

[15]  H. Atwater,et al.  Nanomechanical characterization of cavity growth and rupture in hydrogen-implanted single-crystal BaTiO3 , 2005 .

[16]  Paul S. Ho,et al.  Low Dielectric Constant Materials for ULSI Interconnects , 2000 .

[17]  A. G. Evans,et al.  Measurements of the debond energy for thin metallization lines on dielectrics , 1996 .

[18]  Mechanical properties of porous methyl silsesquioxane and nanoclustering silica films using atomic force microscope , 2010 .

[19]  K. Liechti,et al.  Asymmetric Shielding in Interfacial Fracture Under In-Plane Shear , 1992 .

[20]  Z. Suo,et al.  Mixed mode cracking in layered materials , 1991 .

[21]  M. Madou.  Fundamentals of microfabrication : the science of miniaturization , 2002 .

[22]  O. Chyan,et al.  Electrodeposition of Copper Thin Film on Ruthenium A Potential Diffusion Barrier for Cu Interconnects , 2003 .

[23]  R. Dauskardt,et al.  Comparison of the telephone cord delamination method for measuring interfacial adhesion with the four-point bending method , 2005 .