Rotary-Wing Relevant Compressor Aero Research and Technology Development Activities at Glenn Research Center

Abstract Technical challenges of compressors for future rotorcraft engines are driven by engine-level and component-level requirements. Cycle analyses are used to highlight the engine-level challenges for 3000, 7500, and 12000 SHP-class engines, which include retention of performance and stability margin at low corrected flows, and matching compressor type, axial-flow or centrifugal, to the low corrected flows and high temperatures in the aft stages. At the component level: power-to-weight and efficiency requirements impel designs with lower inherent aerodynamic stability margin; and, optimum engine overall pressure ratios lead to small blade heights and the associated challenges of scale, particularly increased clearance-to-span ratios. The technical challenges associated with the aerodynam-ics of low corrected flows and stability management impel the compressor aero research and development efforts reviewed herein. These activities include development of simple models for clearance sensitivities to improve cycle calculations, full-annulus, unsteady Navier-Stokes simulations used to elucidate stall, its inception, and the physics of stall control by discrete tip-injection, development of an actuator-duct-based model for rapid simulation of nonaxisymmetric flow fields (e.g., due inlet circumferential distortion), advanced centrifugal compressor stage development and experimentation, and application of stall control in a T700 engine.

[1]  M. D. Hathaway,et al.  Flow Characteristics of Tip-Injection on Compressor Rotating Instability via Time-Accurate Simulation , 2010 .

[2]  John J. Adamczyk,et al.  A Post Test Analysis of a High-Speed Two-Stage Axial Flow Compressor , 2007 .

[3]  Scott M. Jones.  An Introduction to Thermodynamic Performance Analysis of Aircraft Gas Turbine Engine Cycles Using the Numerical Propulsion System Simulation Code , 2013 .

[4]  Dennis E. Culley,et al.  Compressor Stall Control Through Endwall Recirculation , 2004 .

[5]  C. C. Koch,et al.  Loss Sources and Magnitudes in Axial-Flow Compressors , 1976 .

[6]  Alan Hale,et al.  A Three-Dimensional Turbine Engine Analysis Compressor Code (TEACC) for Steady-State Inlet Distortion , 1997 .

[7]  Gary J. Skoch,et al.  Performance of two 10-lb/sec centrifugal compressors with different blade and shroud thicknesses operating over a range of Reynolds numbers , 1987 .

[8]  Earl H. Dowell,et al.  A HARMONIC BALANCE APPROACH FOR MODELING THREE-DIMENSIONAL NONLINEAR UNSTEADY AERODYNAMICS AND AEROELASTICITY , 2002 .

[9]  John D. Denton,et al.  Towards long length scale unsteady modelling in turbomachines , 2003 .

[10]  Walter O'Brien,et al.  1997 Best Paper Award—Education Committee: A Three-Dimensional Turbine Engine Analysis Compressor Code (TEACC) for Steady-State Inlet Distortion , 1998 .

[11]  Christopher A. Snyder,et al.  Gas Turbine Characteristics for a Large Civil Tilt-Rotor (LCTR) , 2010 .

[12]  Gary J. Skoch,et al.  An Investigation of Surge in a High-Speed Centrifugal Compressor Using Digital PIV , 2001 .

[13]  J. F. Dugan,et al.  Prediction of off-design performance of multistage compressors , 1965 .

[14]  Gary J. Skoch,et al.  Numerical Simulation of Stall and Stall Control in Axial and Radial Compressors , 2006 .

[15]  M.D. Hathaway,et al.  Unsteady Simulation of the Stall Inception Process in the Compression System of a US Army Helicopter Gas Turbine Engine - Final Year Progress , 2005, 2005 Users Group Conference (DOD-UGC'05).

[16]  Alan H. Epstein,et al.  Active Stabilization of Rotating Stall and Surge in a Transonic Single Stage Axial Compressor , 1997 .

[17]  Michael D. Hathaway,et al.  Pre-Stall Behavior of a Transonic Axial Compressor Stage Via Time-Accurate Numerical Simulation , 2013 .

[18]  Thong Q Dang,et al.  Aerodynamic Design Study of Advanced Multistage Axial Compressor , 2002 .

[19]  Michael D. Hathaway,et al.  Flow Characteristics of Tip Injection on Compressor Rotating Spike via Time-Accurate Simulation , 2009 .

[20]  Richard A. Brokopp,et al.  Small engine components test facility compressor testing cell at NASA Lewis Research Center , 1992 .

[21]  P. S. Prahst,et al.  Aerodynamic Synthesis of a Centrifugal Impeller Using CFD and Measurements , 1997 .

[22]  Edward M. Greitzer,et al.  1997 Best Paper Award—Controls and Diagnostics Committee: Active Stabilization of Rotating Stall and Surge in a Transonic Single-Stage Axial Compressor , 1998 .

[23]  Gary J. Skoch.  Experimental Investigation of Diffuser Hub Injection to Improve Centrifugal Compressor Stability , 2005 .

[24]  Gloria K. Yamauchi,et al.  NASA Heavy Lift Rotorcraft Systems Investigation , 2013 .

[25]  D. C. Wisler,et al.  Loss Reduction in Axial-Flow Compressors Through Low-Speed Model Testing , 1985 .

[26]  Michael D. Hathaway,et al.  Compressor Stability Enhancement Using Discrete Tip Injection , 2000 .

[27]  Gary J. Skoch,et al.  Laser Anemometer Measurements of the Flow Field in a 4:1 Pressure Ratio Centrifugal Impeller , 1997 .

[28]  Gary J. Skoch.  Experimental Investigation of Centrifugal Compressor Stabilization Techniques , 2013 .

[29]  Gerard E. Welch,et al.  Determination of Critical Sector Angle of Inlet Swirl Distortion using Actuator-Duct Model , 2007 .

[30]  Rodrick V. Chima.  A Three-Dimensional Unsteady CFD Model of Compressor Stability , 2013 .

[31]  J. W. Gauntner.  TURBINE COOLING FLOW AND THE RESULTING DECREASE IN TURBINE EFFICIENCY , 1980 .

[32]  Louis M. Larosiliere,et al.  Passage-Averaged Description of Wave Rotor Flow. , 1997 .

[33]  C. W. Acree,et al.  Performance Optimization of the NASA Large Civil Tiltrotor , 2008 .

[34]  J. P. Longley.  Calculating Stall and Surge Transients , 2007 .