The internal calcar septum and its contact with the virtual stem in THRA computer tomographic evaluation

The internal calcar septum is a ridge of cortical bone protruding from the inner cortical wall of the proximal femur into the medullary canal. It extends from the lesser trochanter into the femoral neck and narrows the femoral cavity in its dorsal third. This region is essential for THR stability, but the degree of contact between the septum and standard THR implants has never been studied. We obtained CT scans of 50 arthrotic hip joints from patients requiring THR. Virtual stems (50 straight/wedge-shaped and 50 anatomic stems) were placed in CT images of the femora using a PC-based preoperative planning unit. The dimensions of the septum, degree and location of contact between the septum and implants were recorded. A septum of cortical density was seen in 49/50 CT scans. It was 11 (2.9) mm long (medial-lateral), 3.5 (0.7) mm wide and 32 (10) mm high (caudal-cranial, mean (SD)). 94/100 implanted virtual stems showed direct contact with the septum. 31 straight stems and 5 anatomical stems were supported by the septum along their dorsal side. The internal calcar septum can be consistently seen on CT scans of patients needing THR and it probably contributes to THR stability.

[1]  E. Schneider,et al.  Computertomographische Torsionswinkel- und Längenmessung an der unteren Extremität , 1992 .

[2]  W. Kalender,et al.  Accuracy limits for the determination of cortical width and density: the influence of object size and CT imaging parameters. , 1999, Physics in medicine and biology.

[3]  P. Leyvraz,et al.  The morphology of the proximal femur. A three-dimensional radiographic analysis. , 1992, The Journal of bone and joint surgery. British volume.

[4]  M A Freeman,et al.  Torsional stability of the femoral component of hip arthroplasty. Response to an anteriorly applied load. , 1989, The Journal of bone and joint surgery. British volume.

[5]  W Strecker,et al.  [Computed tomographic torsion-angle and length measurement of the lower extremity. The methods, normal values and radiation load]. , 1992, RoFo : Fortschritte auf dem Gebiete der Rontgenstrahlen und der Nuklearmedizin.

[6]  I Ziv,et al.  The accuracy of computed tomography-based linear measurements of human femora and titanium stem. , 1996, Investigative radiology.

[7]  W. Bargar,et al.  Primary and Revision Total Hip Replacement Using the Robodoc® System , 1998, Clinical orthopaedics and related research.

[8]  A Coblentz,et al.  Micromotion, Fit, and Fill of Custom Made Femoral Stems Designed With an Automated Process , 1996, Clinical orthopaedics and related research.

[9]  F. Merkel.  Betrachtungen über das Os femoris , 2005, Archiv für pathologische Anatomie und Physiologie und für klinische Medicin.

[10]  J Lund-Larsen,et al.  Determination of Hounsfield value for CT-based design of custom femoral stems. , 1999, The Journal of bone and joint surgery. British volume.

[11]  Frank Adam,et al.  The internal calcar septum (femoral thigh spur) in computed tomography and conventional radiography , 2001, Skeletal Radiology.

[12]  P S Walker,et al.  Design and fabrication of cementless hip stems. , 1988, Clinical orthopaedics and related research.

[13]  T P Andriacchi,et al.  Computed tomographic measurement of cortical bone geometry. , 1989, Journal of biomechanics.

[14]  T. Brown,et al.  Mechanical property distributions in the cancellous bone of the human proximal femur. , 1980, Acta orthopaedica Scandinavica.

[15]  C. Bach,et al.  Excessive heat generation during cutting of cement in the Robodoc hip-revision procedure , 2001, Acta orthopaedica Scandinavica.

[16]  H. Tullos,et al.  The anatomic basis of femoral component design. , 1988, Clinical orthopaedics and related research.

[17]  T. Moilanen,et al.  Diversity of proximal femoral medullary canal. , 2000, The Journal of arthroplasty.

[18]  J J Callaghan,et al.  The effect of femoral stem geometry on interface motion in uncemented porous-coated total hip prostheses. Comparison of straight-stem and curved-stem designs. , 1992, The Journal of bone and joint surgery. American volume.

[19]  M Besser,et al.  The utility of histological examination of tissue removed during elective joint replacement. A preliminary assessment. , 1999, The Journal of bone and joint surgery. American volume.

[20]  M. Lehto,et al.  Image processing for femoral endosteal anatomy detection: description and testing of a computed tomography based program. , 1997, Physics in medicine and biology.