Effect of small tool pin profiles on microstructures and mechanical properties of 6061 aluminum alloy by friction stir welding

The effect of small tool pin profiles on the microstructures and mechanical properties of 6061 aluminum alloy joints using friction stir welding (FSW) technique was investigated. Three different tool pin profiles: threaded tapered cylindrical (T1), triangular (T2) and square (T3) were used to produce the joints. The results indicate that the weld joints are notably affected by joining with different tool pin profiles. The triangular tool pin profile produces the best metallurgical and mechanical weld properties compared with other tool pin profiles. Besides, the lowest tensile strength and microhardness are obtained for the joint friction stir welded with square tool pin profile. It is observed that the smaller tool pin profile and shoulder diameter lead to narrow region of heat affected zone (HAZ) and a desired level of softening. The fracture surface examination shows that the joints are also affected when welding with different types of tool pin profiles. The fracture surface shows that the triangular specimen fails with a ductile fracture mode during the tensile test, while the brittle fracture modes are observed in the joints fabricated with other tool pin profiles (T1 and T3).

[1]  P. Asadi,et al.  Investigation of mechanical properties of Cu/SiC composite fabricated by FSP: Effect of SiC particles’ size and volume fraction , 2011 .

[2]  C. Meran.  The joint properties of brass plates by friction stir welding , 2006 .

[3]  V. Balasubramanian,et al.  Microstructure and tensile properties of friction stir welded dissimilar AA6061–AA5086 aluminium alloy joints , 2015 .

[4]  Sanbao Lin,et al.  The influence of pin geometry on bonding and mechanical properties in friction stir weld 2014 Al alloy , 2005 .

[5]  Lawrence E Murr,et al.  Microstructural aspects of the friction-stir welding of 6061-T6 aluminum , 1997 .

[6]  R. Mishra,et al.  Influence of Texture on Mechanical Behavior of Friction-Stir-Processed Magnesium Alloy , 2009 .

[7]  Hugh Shercliff,et al.  Overview No. 124 Modelling of precipitation reactions in industrial processing , 1997 .

[8]  R. Mishra,et al.  Influence of grain size and texture on Hall–Petch relationship for a magnesium alloy , 2011 .

[9]  S. A. Mousavi,et al.  Effects of welding parameters and tool geometry on properties of 3003-H18 aluminum alloy to mild steel friction stir weld , 2013 .

[10]  P. Liaw,et al.  Texture variation and its influence on the tensile behavior of a friction-stir processed magnesium alloy , 2006 .

[11]  Hiroyuki Kokawa,et al.  Parameters controlling microstructure and hardness during friction-stir welding of precipitation-hardenable aluminum alloy 6063 , 2002 .

[12]  S. L. Semiatin,et al.  Continuous dynamic recrystallization during friction stir welding of high strength aluminum alloys , 2000 .

[13]  K. N. Krishnan,et al.  On the formation of onion rings in friction stir welds , 2002 .

[14]  G. Faraji,et al.  Characterization of AZ91/alumina nanocomposite produced by FSP , 2011 .

[15]  Yufeng Sun,et al.  The effect of SiC particles on the microstructure and mechanical properties of friction stir welded pure copper joints , 2011 .

[16]  M. Bahrami,et al.  On the role of pin geometry in microstructure and mechanical properties of AA7075/SiC nano-composite fabricated by friction stir welding technique , 2014 .

[17]  Yong Yan,et al.  Dissimilar friction stir welding between 5052 aluminum alloy and AZ31 magnesium alloy , 2010 .

[18]  J. C. Huang,et al.  Producing nanograined microstructure in Mg–Al–Zn alloy by two-step friction stir processing , 2008 .

[19]  Y. Chen,et al.  Effect of zigzag line on the mechanical properties of friction stir welded joints of an Al–Cu alloy , 2006 .

[20]  Z. Ma,et al.  Enhanced mechanical properties of Mg–Al–Zn cast alloy via friction stir processing , 2007 .

[21]  Y. Chen,et al.  Friction stir welding characteristics of different heat-treated-state 2219 aluminum alloy plates , 2006 .

[22]  L. Murr,et al.  Microstructures in friction-stir welded dissimilar magnesium alloys and magnesium alloys to 6061-T6 aluminum alloy , 2004 .

[23]  T. S. Mahmoud,et al.  Microstructural and mechanical characteristics of AA7020-O Al plates joined by friction stir welding , 2010 .

[24]  M. Bahrami,et al.  A novel approach to develop aluminum matrix nano-composite employing friction stir welding technique , 2014 .

[25]  Anthony P. Reynolds,et al.  Two-dimensional friction stir welding process model based on fluid mechanics , 2003 .

[26]  Carla Gambaro,et al.  Friction stir welding of dissimilar Al 6013-T4 To X5CrNi18-10 stainless steel , 2005 .

[27]  Sung Wook Chung,et al.  Influence of friction stir welding parameters on grain size and formability in 5083 aluminum alloy , 2007 .

[28]  Zhaodong Zhang,et al.  Numerical studies of effect of tool sizes and pin shapes on friction stir welding of AA2024-T3 alloy , 2014 .

[29]  V. Balasubramanian,et al.  Influences of tool pin profile and welding speed on the formation of friction stir processing zone in AA2219 aluminium alloy , 2008 .

[30]  J. C. Huang,et al.  Achieving ultrafine grain size in Mg–Al–Zn alloy by friction stir processing , 2007 .

[31]  A. Kokabi,et al.  Effect of rotational speed and probe profile on microstructure and hardness of AZ31/Al2O3 nanocomposites fabricated by friction stir processing , 2011 .

[32]  M. Fauzi,et al.  Effect of welding speed on mechanical strength of friction welded joint of YSZ–alumina composite and 6061 aluminum alloy , 2011 .

[33]  M. Koçak,et al.  Residual stress in friction stir-welded Al sheets , 2004 .

[34]  K. Maruyama,et al.  Microstructural evolution of a heat-resistant magnesium alloy due to friction stir welding , 2005 .

[35]  Hidetoshi Fujii,et al.  Tensile properties and fracture locations of friction-stir-welded joints of 2017-T351 aluminum alloy , 2003 .

[36]  Robert L. Taylor,et al.  Microstructural studies of friction stir welds in 2024-T3 aluminum , 2002 .

[37]  W. Thomas,et al.  Friction stir welding for the transportation industries , 1997 .