Research on Surface Modification of Polytetrafluoroethylene Coupled With Argon Dielectric Barrier Discharge Plasma Jet Characteristics

An argon dielectric barrier discharge (DBD) atmospheric-pressure plasma jet (APPJ) is designed and employed for surface modification of polytetrafluoroethylene (PTFE). The plasma diagnostics and dielectric surface analysis are coupled together to investigate the mechanisms of plasma modification. The discharge power is obtained by Lissajous figure, and electron excitation temperature (EET) is measured through an optical emission spectrum and calculated by a Boltzmann diagrammatic method. The surface properties of modified PTFE samples are characterized by the static contact angle, surface resistivity, scanning electron microscope (SEM), and X-ray photoelectron spectroscopy. The results show that the discharge power, EET, and surface wettability increase with the Ar flowing rate, and a slight decrease of surface resistivity is revealed after plasma treatment. The surface roughness of PTFE is enhanced, and the oxygen-containing hydrophilic groups are incorporated by the impacts of APPJ radical species. Moreover, the hydrophilicity of PTFE can be improved by a surface presanding process, particularly after APPJ treatment. Finally, the surface modification mechanisms of APPJ on PTFE are discussed.

[1]  K. V. Kozlov,et al.  The barrier discharge: basic properties and applications to surface treatment , 2003 .

[2]  Y. Qiu,et al.  Surface modification of polytetrafluoroethylene film using the atmospheric pressure glow discharge in air , 2003 .

[3]  Hans-Erich Wagner,et al.  Atmospheric Pressure Plasma Jet Treatment of Polyethylene Surfaces for Adhesion Improvement , 2007 .

[4]  I. Kojima,et al.  Application of asymmetrical Gaussian/Lorentzian mixed function for X-ray photoelectron curve synthesis , 1987 .

[5]  L. Peña,et al.  Cell attachment and biocompatibility of polytetrafluoroethylene (PTFE) treated with glow-discharge plasma of mixed ammonia and oxygen , 2003, Journal of biomaterials science. Polymer edition.

[6]  G. Gouda,et al.  A comparison of polypropylene-surface treatment by filamentary, homogeneous and glow discharges in helium at atmospheric pressure , 1998 .

[7]  G. Laroche,et al.  A study of atmospheric pressure plasma discharges for surface functionalization of PTFE used in biomedical applications , 2006 .

[8]  Rachel L. Williams,et al.  Plasma modification of PTFE surfaces. Part II: Plasma‐treated surfaces following storage in air or PBS , 2001 .

[9]  Wjm Wouter Brok,et al.  Experimental and modelling investigations of a dielectric barrier discharge in low-pressure argon , 2006 .

[10]  R. Short,et al.  Using an afterglow plasma to modify polystyrene surfaces in pulsed radio frequency (RF) argon discharges , 2003 .

[11]  In-Seop Lee,et al.  Surface modification of polytetrafluoroethylene using atmospheric pressure plasma jet for medical application , 2007 .

[12]  E. Choi,et al.  Measurement of Electron Temperature and Density Using Stark Broadening of the Coaxial Focused Plasma for Extreme Ultraviolet Lithography , 2010, IEEE Transactions on Plasma Science.

[13]  Y. Qiu,et al.  Polytetrafluoroethylene surface modification by filamentary and homogeneous dielectric barrier discharges in air , 2009 .

[14]  D. Fairbrother,et al.  Effect of wet chemical treatments on the distribution of surface oxides on carbonaceous materials , 2007 .

[15]  T. Chow.  Wetting of rough surfaces , 1998 .

[16]  G. Heinrich,et al.  Modification of PTFE nanopowder by controlled electron beam irradiation: A useful approach for the development of PTFE coupled EPDM compounds , 2008 .

[17]  Youngjong Lee,et al.  Electrospray on superhydrophobic nozzles treated with argon and oxygen plasma , 2008 .

[18]  Rachel Williams,et al.  Plasma modification of PTFE surfaces. Part I: Surfaces immediately following plasma treatment , 2001 .

[19]  A. Rousseau,et al.  Influence of surface charges on the structure of a dielectric barrier discharge in air at atmospheric pressure: experiment and modeling , 2009 .

[20]  D. Aspnes,et al.  Effect of Ar+ ion beam in the process of plasma surface modification of PET films , 2000 .

[21]  M. Okubo,et al.  Preparation of PTFE Film With Adhesive Surface Treated by Atmospheric-Pressure Nonthermal Plasma Graft Polymerization , 2010, IEEE Transactions on Industry Applications.

[22]  J. Roth.  Industrial Plasma Engineering , 1995 .

[23]  U. Kogelschatz.  Dielectric-Barrier Discharges: Their History, Discharge Physics, and Industrial Applications , 2003 .