Optimised hydrodynamics for membrane bioreactors with immersed flat sheet membrane modules

Since aeration is the largest cost factor in membrane bioreactor (MBR) operation it is clear that the biggest leap towards energy and operational costs savings can be achieved by improving the use of air. Many basics of the complex two-phase fl ow in membrane modules and in the overall MBR tank as well as their interactions, however, are still poorly understood. This work focuses both on fundamental studies on shear stress exerted by rising bubbles and on optimising the geometries of tank and module accordingly in order to obtain an improved deposition control at minimum energy input. For both, parameter studies were carried out by numerical simulations which were validated with experimental measurements. The optimum bubble size/channel width combination depended on the superimposed liquid velocity. The relationship between the liquid circulation velocity and the aeration intensity was measured for different reactor and module geometries. A modifi cation of the Chisti model for airlift loop reactors was a...

[1]  R. Lockhart.  Proposed Correlation of Data for Isothermal Two-Phase, Two-Component Flow in Pipes , 1949 .

[2]  J. H. Hills,et al.  The operation of a bubble column at high throughputs: I. Gas holdup measurements , 1976 .

[3]  M. Moo-young,et al.  Gas holdup and overall volumetric oxygen transfer coefficient in airlift contactors , 1985, Biotechnology and bioengineering.

[4]  M. Moo-Young,et al.  Liquid circulation in airlift reactors , 1988 .

[5]  Alain Liné,et al.  Spherical cap bubbles in a flat sheet nanofiltration module: experiments and numerical simulation , 2001 .

[6]  Zhanfeng Cui,et al.  Hydrodynamic analysis of upward slug flow in tubular membranes , 2002 .

[7]  Corinne Cabassud,et al.  Air sparging with flat sheet nanofiltration: a link between wall shear stresses and flux enhancement☆ , 2002 .

[8]  H. Nagaoka,et al.  Measurement of effective shear stress working on flat-sheet membrane by air-scrabbling , 2003 .

[9]  A. Fane,et al.  The use of gas bubbling to enhance membrane processes , 2003 .

[10]  W. J. Ng,et al.  Engineering design approaches for minimum fouling in submerged MBR , 2004 .

[11]  Tom Stephenson,et al.  Biomass characteristics and membrane aeration: toward a better understanding of membrane fouling in submerged membrane bioreactors (MBRs). , 2005, Biotechnology and bioengineering.

[12]  Ewan McAdam,et al.  Critical analysis of submerged membrane sequencing batch reactor operating conditions. , 2005, Water research.

[13]  Anthony G. Fane,et al.  Low pressure membrane processes - doing more with less energy , 2005 .

[14]  David F. Fletcher,et al.  Fouling Control in a Submerged Flat Sheet Membrane System: Part II—Two‐Phase Flow Characterization and CFD Simulations , 2006 .

[15]  N. V. Ndinisa,et al.  Fouling Control in a Submerged Flat Sheet Membrane System: Part I – Bubbling and Hydrodynamic Effects , 2006 .

[16]  S Judd,et al.  The cost of a package plant membrane bioreactor. , 2007, Water research.

[17]  Adrian Wing-Keung Law,et al.  The relationship between performance of submerged hollow fibers and bubble-induced phenomena examined by particle image velocimetry , 2007 .

[18]  H. Prieske,et al.  Prediction of the circulation velocity in a membrane bioreactor , 2008 .

[19]  Matthias Kraume,et al.  Optimierung der Blasen- und Zirkulationsströmung in Membranbelebungsreaktoren† , 2008 .

[20]  Corinne Cabassud,et al.  Gas/Liquid Two-phase Flow in a Flat Sheet Filtration Module: Measurement of Local Wall Shear Stresses , 2008 .

[21]  C. Brepols,et al.  An aeration energy model for an immersed membrane bioreactor. , 2008, Water research.

[22]  Z. Cui,et al.  Effect of bubble size and frequency on mass transfer in flat sheet MBR , 2009 .

[23]  H. Prieske,et al.  Advantageous and detrimental effects of air sparging in membrane filtration: Bubble movement, exerted shear and particle classification , 2010 .