A Multi-Tier Design Methodology for Reconfigurable Milling Machines

Reconfigurable Machine Tools (RMTs) have been developed in response to agile flexible manufacturing demands. Current design methodologies for RMTs support modular reconfigurability in which a machine configuration is assembled for a given part. In this paper, on the other hand, reconfigurability relies on redundancy, namely, a desired RMT configuration is obtained through topological reconfiguration by locking/unlocking degrees-of-freedom (dof). Thus, in order to design a Redundant Reconfigurable Machine Tool (RRMT) with all of its dof already included, a new multi–tier optimization based design methodology was developed. The design is formulated for the efficient selection of the best architecture from a set of serial/parallel/hybrid solutions, while considering the redundant reconfigurability effect on performance. The viability of the methodology is demonstrated herein via a design test case of a Parallel Kinematic Mechanism (PKM)-based Redundant Reconfigurable meso-Milling Machine Tool (RRmMT) that can attain high stiffness at the high feed-rate required in meso-milling.

[1]  Eric Courteille,et al.  Off-line compensation of the tool path deviations on robotic machining: Application to incremental sheet forming , 2013 .

[2]  Yong Mo Moon,et al.  Design of Reconfigurable Machine Tools , 2002 .

[3]  Craig A. Phillips,et al.  Trajectory Optimization for a Missile Using a Multitier Approach , 2000 .

[4]  Kai Cheng,et al.  Micro-Cutting: Fundamentals and Applications , 2013 .

[5]  Li Chen,et al.  Optimal Module Selection for Preliminary Design of Reconfigurable Machine Tools , 2005 .

[6]  Lihui Wang,et al.  Parallel Kinematic Machines: Design, Analysis and Simulation in an Integrated Virtual Environment , 2005 .

[7]  Dan Zhang,et al.  Parallel Robotic Machine Tools , 2009 .

[8]  Richard E. DeVor,et al.  A new acceleration-based methodology for micro/meso-scale machine tool performance evaluation , 2006 .

[9]  Tuğrul Özel,et al.  Meso/micro scale milling for micro-manufacturing , 2008 .

[10]  Richard E. DeVor,et al.  Development of an automated microfactory: Part 1 - Microfactory architecture and sub-systems development , 2006 .

[11]  Lothar Bohn,et al.  Microstructure grooves with a width of less than 50 μm cut with ground hard metal micro end mills , 1999 .

[12]  Arturo Molina,et al.  Development of an Integrated Approach to the Design of Reconfigurable Micro/Mesoscale CNC Machine Tools , 2014 .

[13]  Frank Chongwoo Park,et al.  Design and analysis of a redundantly actuated parallel mechanism for rapid machining , 2001, IEEE Trans. Robotics Autom..

[14]  Z. M. Bi,et al.  Development of reconfigurable machines , 2008 .

[15]  Fritz Klocke,et al.  Size Effects in Micro Drilling Ferritic-Pearlitic Carbon Steels , 2012 .

[16]  Manfred Weck,et al.  Parallel Kinematic Machine Tools – Current State and Future Potentials , 2002 .

[17]  Anjan Kumar Dash,et al.  Task-oriented configuration design for reconfigurable parallel manipulator systems , 2005, Int. J. Comput. Integr. Manuf..

[18]  Hélène Chanal,et al.  Process definition of preformed part machining for taking benefit of parallel kinematic machine tool kinematic performances , 2012 .

[19]  Beno Benhabib,et al.  A multi-arm robotic system for optimal sculpting , 2008 .

[20]  Wei Liu,et al.  Multi-objective design optimization of reconfigurable machine tools: a modified fuzzy-Chebyshev programming approach , 2008 .

[21]  Taejung Kim,et al.  A hybrid 5-axis CNC milling machine , 2009 .

[22]  Khalifa H. Harib,et al.  A hexapod-based machine tool with hybrid structure: Kinematic analysis and trajectory planning , 2007 .

[23]  Doina Pisla,et al.  Structural design and kinematics of a new parallel reconfigurable robot , 2013 .

[24]  Beno Benhabib,et al.  Comparative analysis of a new 3×PPRS parallel kinematic mechanism , 2014 .

[25]  Wei Ye,et al.  A new family of reconfigurable parallel mechanisms with diamond kinematotropic chain , 2014 .

[26]  Fengfeng Xi,et al.  Reconfiguration Analysis of a Fully Reconfigurable Parallel Robot , 2013 .

[27]  Christian Soize,et al.  Robust Design Optimization in Computational Mechanics , 2008 .

[28]  M. Kannan,et al.  A feature-based generic setup planning for configuration synthesis of reconfigurable machine tools , 2009 .

[29]  Lihui Wang,et al.  Optimal design of reconfigurable parallel machining systems , 2009 .

[30]  Zhuming Bi,et al.  Enhancement of Adaptability of Parallel Kinematic Machines With an Adjustable Platform , 2010 .

[31]  Chin-Yin Chen,et al.  Integrated design for a mechatronic feed drive system of machine tools , 2005, Proceedings, 2005 IEEE/ASME International Conference on Advanced Intelligent Mechatronics..