The General Method for the fire design of slender I-section web-tapered columns

Abstract The purpose of this paper is to validate the General Method for the stability check of unrestrained I-section web-tapered columns in fire situation. The General Method (clause 6.3.4 of EN 1993-1-1) covers the safety check of structural elements with complex support conditions and/or of non-prismatic members. However, the fire part of the Eurocode 3 (EN 1993-1-2) gives no further indication regarding the applicability of the method at elevated temperatures, apart from adapting the methodology to fire using the reduction factors for steel material properties, which is identified as a gap in the current version of the norm. To ascertain the validity of said adaptations, the ultimate capacity of members at elevated temperature has been obtained numerically with GMNI-Analyses and a parametric investigation incorporating I-section web-tapered columns built from slender (class 4) cross-sections has been carried out, with special attention to the influence of local buckling on member stability. It has been demonstrated that a straightforward application of the temperature-reduced mechanical properties of steel in the General Method results in an unsafe methodology, therefore justifying improvements to the procedure. In this work, this is done by i) proposing a novel methodology for the calculation of the in-plane load amplifier α u l t , k and ii) recalibrating the EN 1993-1-2 buckling curve. Not only does this new procedure improve the accuracy of the methodology but it also foregoes the otherwise necessary evaluation of the critical cross-section along the column.

[1]  J. P. Muzeau,et al.  Design of tapered compression members according to Eurocode 3 , 1998 .

[2]  Andrea Frangi,et al.  Cross‐sectional capacity and flexural buckling resistance under fire conditions , 2014 .

[3]  Jean-Marc Franssen,et al.  Experimental tests and numerical modelling on eight slender steel columns under increasing temperatures , 2014 .

[4]  João Martins,et al.  Experimental buckling behaviour of web tapered I-section steel columns , 2018, Journal of Constructional Steel Research.

[5]  George C. Lee,et al.  Design of Tapered Members. , 1971 .

[6]  Luís Simões da Silva,et al.  Development of a consistent buckling design procedure for tapered columns , 2012 .

[7]  António M. Correia,et al.  Fire resistance of steel columns with restrained thermal elongation , 2012 .

[8]  Kuo-Chen Yang,et al.  Experimental study of fire-resistant steel H-columns at elevated temperature , 2006 .

[9]  Luís Simões da Silva,et al.  Development of a consistent design procedure for lateral-torsional buckling of tapered beams , 2013 .

[10]  Paulo Vila Real,et al.  Stability check of tapered steel beams in fire , 2019 .

[11]  Hiroyuki Shiomi,et al.  TESTS ON TAPERED STEEL BEAM-COLUMNS , 1983 .

[12]  Carlos Couto,et al.  Comparison of the General Method with the Overall Method for the out-of-plane stability of members with lateral restraints , 2017 .

[13]  Jean-Marc Franssen,et al.  A simple model for the fire resistance of axially-loaded members according to eurocode 3 , 1995 .

[14]  João Martins,et al.  Experimental lateral-torsional buckling behaviour of web tapered I-section steel beams , 2018, Engineering Structures.

[15]  Jean-Marc Franssen,et al.  Modeling structures in fire with SAFIR®: Theoretical background and capabilities , 2017 .

[16]  Paulo Vila Real,et al.  The effect of non-uniform bending on the lateral stability of steel beams with slender cross-section at elevated temperatures , 2018 .

[17]  Paulo Vila Real,et al.  Numerical investigation on the influence of imperfections in the local buckling of thin-walled I-shaped sections , 2019, Thin-Walled Structures.

[18]  Adrian Ioan Dogariu,et al.  Experimental study on laterally restrained steel columns with variable I cross sections , 2012 .

[19]  Paulo Vila Real,et al.  Resistance of steel cross-sections with local buckling at elevated temperatures , 2015 .

[20]  Marian Giżejowski,et al.  Buckling resistance of steel H-section beam–columns: In-plane buckling resistance , 2019, Journal of Constructional Steel Research.

[21]  Liliana Marques,et al.  Buckling resistance of non-uniform steel members based on stress utilization: General formulation , 2018, Journal of Constructional Steel Research.

[22]  Carlos Rebelo,et al.  Numerical validation of the general method in EC3-1-1 for prismatic members , 2010 .

[23]  S. Timoshenko.  Theory of Elastic Stability , 1936 .

[24]  František Wald,et al.  Lateral-torsional buckling of class 4 section uniform and web tapered beams at elevated temperature , 2020 .

[25]  Desmond Robinson,et al.  Novel loading tests on full-scale tapered member portal frames , 2009 .

[26]  Carlos Couto,et al.  Numerical investigation of the lateral–torsional buckling of beams with slender cross sections for the case of fire , 2016 .

[27]  Aldina Santiago,et al.  The effect of residual stresses in the lateral-torsional buckling of steel I-beams at elevated temperature , 2004 .

[28]  Guo-Qiang Li,et al.  Large-Scale Testing of Steel Portal Frames Comprising Tapered Beams and Columns , 2002 .

[29]  Chrysanthos Maraveas,et al.  Local Buckling of Steel Members Under Fire Conditions: A Review , 2018, Fire Technology.

[30]  Jean-Marc Franssen,et al.  A Quadrangular Shell Finite Element for Concrete and Steel Structures Subjected to Fire , 2005 .

[31]  Paulo Vila Real,et al.  Effective width method to account for the local buckling of steel thin plates at elevated temperatures , 2014 .

[32]  Mario Fontana,et al.  Strain-based approach to local buckling of steel sections subjected to fire , 2006 .

[33]  František Wald,et al.  Experiments of Class 4 open section beams at elevated temperature , 2016 .

[34]  Kuo-Chen Yang,et al.  Performance of steel H columns loaded under uniform temperature , 2006 .

[35]  Liliana Raquel Simões Marques.  Tapered steel members : flexural and lateral-torsional buckling , 2012 .

[36]  Yoon Duk Kim,et al.  Behavior and design of metal building frames using general prismatic and web-tapered steel I-section members , 2010 .

[37]  Guo-Qiang Li,et al.  A second-order inelastic model for steel frames of tapered members with slender web , 2003 .

[38]  Hiroyuki Shiomi,et al.  Strength Formula for Tapered Beam‐Columns , 1984 .