A smart segmented blade system for reducing weight of the wind turbine rotor

The paper proposes a novel design concept for the wind turbine rotors. The design is composed of the segmented blades and a hinged-rods support structure (SBHR) as a means of reducing weight through alleviating the moment on the blade. A prototype of the design is manufactured. Focusing on the hinged-rods support structure (HRSS), a method combining the experiments and numerical calculation is developed to analyze its feasibility. The experiments in the wind tunnel platform were conducted to measure the loads at the root of the isolated blade and in the rods. A numerical model was developed to describe the designed wind turbine rotor using the measured loads in experiments. In the model, the mounting locations of the hinged rods significantly affected the moment distribution on the blade. Thus, two dimensionless indexes were determined to analyze its influences. The model perfectly explain the characteristics of the novel structure under different configurations. The results demonstrated that the moment of the blade below the hinged location were alleviated, which reduced the requirements for the material. A 43.1% reduction of the maximum moment can be achieved in the design. In addition, the gross reduced weight of the blade was estimated to be 35.4% based on the blade mass distribution along the span.

[1]  Mac Gaunaa,et al.  Load alleviation through adaptive trailing edge control surfaces: ADAPWING overview , 2007 .

[2]  Paul M. Weaver,et al.  Review of morphing concepts and materials for wind turbine blade applications , 2013 .

[3]  Robert J. Moffat,et al.  Describing the Uncertainties in Experimental Results , 1988 .

[4]  Michael S. Selig,et al.  Morphing Segmented Wind Turbine Concept , 2010 .

[5]  Maureen Hand,et al.  NREL Unsteady Aerodynamics Experiment in the NASA-Ames Wind Tunnel: A Comparison of Predictions to Measurements , 2001 .

[6]  Désiré Le Gouriérès.  Wind Power Plants: Theory and Design , 1982 .

[7]  M.R.H. Nobari,et al.  Prediction of optimum section pitch angle distribution along wind turbine blades , 2013 .

[8]  C. Kong,et al.  Structural investigation of composite wind turbine blade considering various load cases and fatigue life , 2005 .

[9]  Fouad Bennis,et al.  Optimal Design of a Simplified Morphing Blade for Fixed-Speed Horizontal Axis Wind Turbines , 2012, DAC 2012.

[10]  A. Huskey.  International Electrotechnical Commission Standard IEC 61400-11 and Other Procedures: Acoustic Noise Measurement Techniques , 2006 .

[11]  D. Thirumalai.  Future Materials for Wind Turbine Blades - A Critical Review , 2012 .

[12]  Robert Thresher,et al.  Advanced Wind Technology: New Challenges for a New Century , 2006 .

[13]  Matthew A. Lackner,et al.  A comparison of smart rotor control approaches using trailing edge flaps and individual pitch control , 2009 .

[14]  Kevin Cox,et al.  Structural Design and Analysis of a 10MW Wind Turbine Blade , 2012 .

[15]  Paul M. Weaver,et al.  Design and testing of a deformable wind turbine blade control surface , 2012 .

[16]  Daniel J. Inman,et al.  Design and Wind-Tunnel Analysis of a Fully Adaptive Aircraft Configuration , 2004 .

[17]  Mohammad Rezaei Mirghaed,et al.  Site specific optimization of wind turbines energy cost: Iterative approach , 2013 .

[18]  Jiuyue Xu,et al.  Blade layers optimization of wind turbines using FAST and improved PSO Algorithm , 2012 .

[19]  Philippe Leconte,et al.  SOFT ROTOR DESIGN FOR FLEXIBLE TURBINES , 1998 .

[20]  Ole Thybo Thomsen,et al.  Sandwich Materials for Wind Turbine Blades — Present and Future , 2009 .

[21]  D. Thirumalai.  A critical review of future materials for wind turbine blades , 2014 .

[22]  Adam Steele,et al.  Segmented Ultralight Pre-Aligned Rotor for Extreme-Scale Wind Turbines , 2012 .

[23]  Timoleon Kipouros,et al.  Multi-objective optimisation of horizontal axis wind turbine structure and energy production using aerofoil and blade properties as design variables , 2014 .