Variability of unconfined compressive strength in relation to number of test samples

Unconfined compressive strength is one of the most commonly used properties in rock engineering. Estimation or selection of an appropriate value of unconfined compressive strength for a given rock can be difficult as it can vary greatly within the same rock unit. Considering this large variability, unconfined compressive strength obtained by testing just a few samples is questionable. The purpose of this study was to investigate the variability of unconfined compressive strength for a given rock and, based on this information, determine the minimum number of samples required for obtaining a reliable value. Unconfined compressive strength values for approximately 50 NX-size (2.125 in./5.4 cm) core samples were determined for five different rock types. Statistical analyses were performed on subsets of cores to determine the minimum number of samples required to render a reliable estimate of the average strength of the entire set of cores. The results indicate that the minimum number of samples needed for strength determination depends on the statistical method used, the chosen confidence interval, and the acceptable deviation from the mean. For a 95% confidence interval and a 20% acceptable strength deviation from the mean, either 9 or 10 samples are needed to test for strength, depending on the statistical analysis used.

[1]  Eric R. Ziegel,et al.  Applied Statistics for Engineers and Physical Scientists , 1992 .

[2]  A. B. Hawkins,et al.  Aspects of rock strength , 1998 .

[3]  J. Pitts.  A manual of geology for civil engineers , 1984 .

[4]  Celal Karpuz,et al.  A probabilistic model for the assessment of uncertainties in the shear strength of rock discontinuities , 2002 .

[5]  G. Melissa,et al.  The relationship between tensile and compressive strengths for selected sandstones as influenced by index properties and petrographic characteristics , 1994 .

[6]  Graham J. Borradaile,et al.  Statistics of Earth Science Data: Their Distribution in Time, Space and Orientation , 2003 .

[7]  Evert Hoek,et al.  Rock fracture under static stress conditions , 1965 .

[8]  W. Brace.  Dependence of Fracture Strength of Rocks on Grain Size , 1961 .

[9]  G. White,et al.  Variability in unconfined compression strength of pavement materials stabilised with cementitious binders , 2003 .

[10]  J. Rohde,et al.  Analysis of the variability of unconfined compression tests of rock , 1990 .

[11]  William A. Olsson,et al.  Grain size dependence of yield stress in marble , 1974 .

[12]  Sung-Chi Hsu,et al.  Characterization of Eagle Ford Shale , 2002 .

[13]  F. Bell.  The physical and mechanical properties of the fell sandstones, Northumberland, England , 1978 .

[14]  U. Yamaguchi,et al.  The number of test-pieces required to determine the strength of rock , 1970 .

[15]  Richard J. Block,et al.  3 – PART A , 1960 .

[16]  R. Corotis.  Probability and statistics in Civil Engineering: by G.N. Smith, Nichols Publishing Company, New York, NY, 1986, 244 pp. , 1988 .

[17]  Celal Karpuz,et al.  Rock variability and establishing confining pressure levels for triaxial tests on rocks , 2006 .

[18]  R. Ulusay,et al.  Prediction of engineering properties of a selected litharenite sandstone from its petrographic characteristics using correlation and multivariate statistical techniques , 1994 .

[19]  R. Lama.  Handbook on Mechanical Properties of Rocks , 1978 .

[20]  A. B. Hawkins,et al.  Sensitivity of sandstone strength and deformability to changes in moisture content , 1992, Quarterly Journal of Engineering Geology.

[21]  L. Dobereiner,et al.  Evaluating the strength and deformability of sandstones , 1991, Quarterly Journal of Engineering Geology.

[22]  E. M. Winkler,et al.  A durability index for stone , 1985 .

[23]  Alan Hartley,et al.  A review of the geological factors influencing the mechanical properties of road surface aggregates , 1974, Quarterly Journal of Engineering Geology.

[24]  William Cyrus Navidi,et al.  Statistics for Engineers and Scientists , 2004 .

[25]  Z. T. Bieniawski,et al.  Suggested methods for determining the uniaxial compressive strength and deformability of rock materials: Part 1. Suggested method for determination of the uniaxial compressive strength of rock materials , 1979 .

[26]  M. H. Leite,et al.  Determining the minimal number of specimens for laboratory testing of rock properties , 2005 .

[27]  V. Palchik.  Influence of Porosity and Elastic Modulus on Uniaxial Compressive Strength in Soft Brittle Porous Sandstones , 1999 .

[28]  D. Coates,et al.  Experimental criteria for classification of rock substances , 1966 .

[29]  Z. Bieniawski.  Estimating the strength of rock materials , 1974 .

[30]  M. Fahy,et al.  Estimating Strength of Sandstone Using Petrographic Thin-Section Data , 1979 .

[31]  Chris Spatz,et al.  Basic Statistics: Tales of Distributions , 1981 .

[32]  S. Singh.  Relationship among fatigue strength, mean grain size and compressive strength of a rock , 1988 .

[33]  Abdul Shakoor,et al.  A Laboratory Investigation of the Effects of Cyclic Heating and Cooling, Wetting and Drying, and Freezing and Thawing on the Compressive Strength of Selected Sandstones , 2003 .

[34]  Karl V. Bury,et al.  Statistical Distributions in Engineering: Statistics , 1999 .