Optimization of friction properties of kenaf polymer composite as an alternative friction material

Purpose The aim of this study is to determine the optimal parameters for friction coefficient of kenaf/epoxy (KE) composite as an alternative friction material. Design/methodology/approach The design of experiment was constructed using the Taguchi method. KE specimens were formed into 10 mm diameter pins using hot compression technique with different types, weight concentrations and treatments of kenaf. The samples were tested using a pin-on-disc tribometer at different applied loads, speeds and operating temperatures with a constant sliding distance of 3 km under dry sliding conditions. Findings The sample with 45 wt.% of non-treated kenaf fibre, tested at 19.62 N, 500 rpm and 100°C was found to be the optimized combination to obtain higher friction. From the confirmation test, the experimental friction coefficient is acceptable because of fall within 95 per cent confidence interval. Predominant wear mechanisms are identified as micro-crack and debonding of fibre. Originality/value KE composite can be considered as an alternative friction material, as the tested friction coefficient is within the suggested range for the friction material applications.

[1]  H. Unal,et al.  Thermal, mechanical and tribological performance of polymer composites rubbed against polymer composites in application in electrical contact breakers , 2014 .

[2]  V. Auradi,et al.  Influence of Combined Addition of Boron and Strontium on High-Temperature Wear Behavior of A356 Alloy , 2016 .

[3]  B. F. Yousif,et al.  Betelnut fibres as an alternative to glass fibres to reinforce thermoset composites: A comparative study , 2012 .

[4]  H. Choi,et al.  A Review: Natural Fiber Composites Selection in View of Mechanical, Light Weight, and Economic Properties , 2015 .

[5]  Qihua Wang,et al.  Effect of resins on thermal, mechanical and tribological properties of friction materials , 2015 .

[6]  A. Satapathy,et al.  A comparative study on erosion characteristics of red mud filled bamboo–epoxy and glass–epoxy composites , 2010 .

[7]  Jayashree Bijwe,et al.  Composites as friction materials: Recent developments in non‐asbestos fiber reinforced friction materials—a review , 1997 .

[8]  P. Wambua,et al.  Natural fibres: can they replace glass in fibre reinforced plastics? , 2001 .

[9]  B. F. Yousif,et al.  Adhesive Wear Performance of T-OPRP and UT-OPRP Composites , 2008 .

[10]  Long Zhang,et al.  Microstructure Characteristics and Properties of HVOF Sprayed Ni-Based Alloy Nano-h-BN Self-Lubricating Composite Coatings , 2015 .

[11]  B. F. Yousif,et al.  Characteristics of kenaf fibre/epoxy composites subjected to thermal degradation , 2013 .

[12]  P. Sahoo,et al.  Optimization of wear behavior of electroless Ni-P-W coating under dry and lubricated conditions using genetic algorithm (GA) , 2016 .

[13]  A. Jourani,et al.  Friction and Wear Mechanisms of 316L Stainless Steel in Dry Sliding Contact: Effect of Abrasive Particle Size , 2015 .

[14]  M. S. Meon,et al.  Improving Tensile Properties of Kenaf Fibers Treated with Sodium Hydroxide , 2012 .

[15]  Maya Jacob John,et al.  Biofibres and Biocomposites , 2008 .

[16]  Qihua Wang,et al.  Friction and Wear of Potassium Titanate Whisker Filled Carbon Fabric/Phenolic Polymer Composites , 2015 .

[17]  B. F. Yousif,et al.  Potential of kenaf fibres as reinforcement for tribological applications , 2009 .

[18]  Qihua Wang,et al.  Formulation Optimization of Friction Material with Golden Section Approach , 2016 .

[19]  B. F. Yousif,et al.  Adhesive Wear of Thermoplastic Composite Based on Kenaf Fibres , 2011 .

[20]  A. Patnaik,et al.  Wear Behavior of Plant Fiber (Pine-Bark) and Cement Kiln Dust-Reinforced Polyester Composites Using Taguchi Experimental Model , 2010 .

[21]  V. Srivastava,et al.  Tribological Behavior of Particles and Fiber-Reinforced Hybrid Nanocomposites , 2015 .

[22]  Staffan Jacobson,et al.  On the nature of tribological contact in automotive brakes , 2002 .