Fatigue limit assessment on seamless tubes in presence of inhomogeneities: Small crack model vs. full scale testing experiments

Abstract The existence of crack-like flaws cannot be excluded in pressure vessels and piping due to the presence of non-metallic inclusions and surface imperfections. These inhomogeneities reduce the fatigue strength of the pressure vessel. In this work, the detrimental effect of the surface quality on the fatigue strength of cylinder housings is analyzed by means of a fatigue model available in the literature using values obtained by crack propagation tests. The comparison in terms of fatigue limit between model and experimental full scale (FS) tests has shown an underestimation of the fatigue strength if the prediction based on Δ K th,LC values for long cracks is used. This is due to a flattening effect of the Δ K th,LC values at high stress ratios R under full scale tests that the standard crack propagation tests do not anticipate. Further investigations need to be carried out for more realistic prediction by the mentioned model. In order to obtain an accurate and more realistic fatigue limit, an alternative small scale (SS) fatigue test has been implemented. The goal was to reproduce as much as possible the real condition of a full scale (FS) state during the small scale (SS) fatigue limit test; and this has led to a good agreement between the FS and SS fatigue limit tests.

[1]  Andrea Carpinteri,et al.  A three-parameter model for fatigue behaviour of circumferential surface flaws in pipes , 2000 .

[2]  M. Carboni,et al.  Determination of Δ K th by Compression Pre-Cracking in a Structural Steel , 2009 .

[3]  C. Sonsino.  Course of SN-curves especially in the high-cycle fatigue regime with regard to component design and safety , 2007 .

[4]  M. Dankert,et al.  AN ANALYTICAL PROCEDURE FOR PREDICTING OPENING LOADS OF CRACKS AT NOTCHES , 1995 .

[5]  F. M. Burdekin,et al.  Engineering critical analyses to BS 7910 — the UK guide on methods for assessing the acceptability of flaws in metallic structures , 2000 .

[6]  V. Shlyannikov.  Fatigue shape analysis for internal surface flaw in a pressurized hollow cylinder , 2000 .

[7]  B. Fedelich,et al.  Corrosion Books: Metal Fatigue: Effects of Small Defects and Nonmetallic Inclusions. By Y. Murakami. ‐ Materials and Corrosion 3/2003 , 2003 .

[8]  M. Okayasu,et al.  Experimental study of the effect of loading condition on fracture surface contact features and crack closure behavior in a carbon steel , 2006 .

[9]  J. Newman,et al.  Compression Precracking Methods to Generate Near-Threshold Fatigue-Crack-Growth-Rate Data , 2010 .

[10]  H. L. Stark,et al.  Review of fatigue design procedures for pressure vessels , 2000 .

[11]  Jaap Schijve,et al.  Fatigue of structures and materials , 2001 .

[12]  D. Holm,et al.  Growth of cracks under far-field cyclic compressive loads: numerical and experimental results , 1986 .

[13]  James C. Newman,et al.  An empirical stress-intensity factor equation for the surface crack , 1981 .

[14]  Jerzy Rojek,et al.  Practical fatigue analysis of hydraulic cylinders and some design recommendations , 2006 .

[15]  Katsumasa Miyazaki,et al.  Fatigue strength for pipes with allowable flaws and design fatigue curve , 2002 .

[16]  Stefano Beretta,et al.  STATISTICAL ANALYSIS OF DEFECTS FOR FATIGUE STRENGTH PREDICTION AND QUALITY CONTROL OF MATERIALS , 1998 .

[17]  Subra Suresh,et al.  Crack initiation in cyclic compression and its applications , 1985 .

[18]  Stefano Beretta,et al.  Structural integrity assessment validation of seamless tubes for hydraulic cylinders using „fitness for service“ concepts , 2010 .

[19]  X. B. Lin,et al.  Numerical analysis of fatigue growth of external surface cracks in pressurised cylinders , 1997 .

[20]  R. C. Mcmaster.  Nondestructive testing handbook , 1959 .

[21]  Franz Rauscher,et al.  Fatigue of non-welded pressure vessels made of high strength steel , 2003 .

[22]  M. E. Haddad,et al.  Fatigue Crack Propagation of Short Cracks , 1979 .

[23]  A. Bakker.  Mechanical Behaviour of Materials , 1995 .

[24]  Marco Giglio,et al.  Fatigue analysis of different types of pressure vessel nozzle , 2003 .

[25]  Y. Murakami.  Metal Fatigue: Effects of Small Defects and Nonmetallic Inclusions , 2002 .

[26]  D. Holm,et al.  Load Interaction Effects on Compression Fatigue Crack Growth in Ductile Solids , 1988 .

[27]  Masahiro Endo,et al.  Defect tolerant design of automotive components , 1997 .

[28]  Stefano Beretta,et al.  Correlation Between Experiments and Strip Yield Model Results on Fatigue Crack Growth in a Structural Steel , 2002 .