Numerical study of the pressure drop phenomena in wound woven wire matrix of a Stirling regenerator

Abstract Friction pressure drop correlation equations are derived from a numerical study by characterizing the pressure drop phenomena through porous medium of both types namely stacked and wound woven wire matrices of a Stirling engine regenerator over a specified range of Reynolds number, diameter and porosity. First, a finite volume method (FVM) based numerical approach is used and validated against well known experimentally obtained empirical correlations for a misaligned stacked woven wire matrix, the most widely used due to fabrication issues, for Reynolds number up to 400. The friction pressure drop correlation equation derived from the numerical results corresponds well with the experimentally obtained correlations with less than 5% deviation. Once the numerical approach is validated, the study is further extended to characterize the pressure drop phenomena in a wound woven wire matrix model of a Stirling engine regenerator for a diameter range from 0.080 to 0.110 mm and a porosity range from 0.472 to 0.638 within the same Reynolds number range. Thus, the new correlation equations are derived from this numerical study for different flow configurations of the Stirling engine regenerator. The results indicate flow nature and complex geometry dependent friction pressure drop characteristics within the present Stirling engine regenerator system. It is believed that the developed correlations can be applied with confidence as a cost effective solution to characterize and hence to optimize stacked and woven Stirling engine efficiency in the above specified ranges.

[1]  Eldesouki I. Eid,et al.  Development of the performance of an alpha-type heat engine by using elbow-bend transposed-fluids heat exchanger as a heater and a cooler , 2011 .

[2]  Iwao Yamashita,et al.  Flow and Heat Transfer Characteristics of the Stirling Engine Regenerator in an Oscillating Flow , 1990 .

[3]  D. Gedeon,et al.  Oscillating-Flow Regenerator Test Rig: Hardware and Theory With Derived Correlations for Screens and Felts , 1996 .

[4]  R. V. Edwards,et al.  A New Look at Porous Media Fluid Mechanics — Darcy to Turbulent , 1984 .

[5]  Henrik Carlsen,et al.  Numerical study on optimal Stirling engine regenerator matrix designs taking into account the effects of matrix temperature oscillations , 2006 .

[6]  S. Orszag,et al.  Renormalization group analysis of turbulence. I. Basic theory , 1986, Physical review letters.

[7]  Rodger W. Dyson,et al.  Overview 2004 of NASA Stirling-Convertor Cfd-Model Development and Regenerator R&d Efforts , 2013 .

[8]  Allan J. Organ,et al.  The Regenerator and the Stirling Engine , 1997 .

[9]  Terrence W. Simon,et al.  Computational modeling of a segmented-involute-foil regenerator for stirling engines , 2009 .

[10]  Iskander Tlili,et al.  PERFORMANCE OPTIMIZATION OF STIRLING ENGINES , 2008 .

[11]  A. E. Holdø,et al.  Computational modelling of flow around a circular cylinder in sub-critical flow regime with various turbulence models , 2001 .

[12]  Qiang Li,et al.  Evaluation of thermal efficiency and energy conversion of thermoacoustic Stirling engines , 2010 .

[13]  Israel Urieli,et al.  Stirling Cycle Engine Analysis , 1983 .

[14]  I. Rühlich,et al.  New regenerator design for cryocoolers , 1998 .

[15]  Allan J. Organ,et al.  Thermodynamics and Gas Dynamics of the Stirling Cycle Machine , 1992 .

[16]  Viktor Dorer,et al.  Energy and CO2 emissions performance assessment of residential micro-cogeneration systems with dynamic whole-building simulation programs , 2009 .

[17]  Terrence W. Simon,et al.  A survey of oscillating flow in Stirling engine heat exchangers , 1988 .

[18]  S. Orszag,et al.  Renormalization group analysis of turbulence. I. Basic theory , 1986 .

[19]  Ghislain Despesse,et al.  Analytical model for Stirling cycle machine design , 2010 .

[20]  S. Ergun.  Fluid flow through packed columns , 1952 .

[21]  José Ricardo Sodré,et al.  Friction Factor Determination for Flow Through Finite Wire-Mesh Woven-Screen Matrices , 1997 .

[22]  H Miyabe,et al.  An approach to the design of stirling engine regenerator matrix using packs of wire gauzes. , 1982 .