Finite time thermodynamic analysis of small alpha-type Stirling engine in non-ideal polytropic conditions for recovery of LNG cryogenic exergy

Abstract In the paper, a second order thermodynamic analysis of a small scale alpha-type Stirling engine is presented. The developed mathematical model is based on the Finite Time Thermodynamics (FFT) approach and it is derived from the differential time dependent equations of energy and mass conservation. The engine model consists of three spaces: compression, expansion and regenerator. In contrast to available models, the model presented in this paper assumes polytropic processes in the compression and expansion spaces, which corresponds to the non-ideal heat transfer in these spaces. The results, obtained using the developed second order model, were compared with the results obtained using the Computational Fluid Dynamics (CFD) analysis of the same engine. A very good agreement between the second order model and the CFD model was achieved. Finally, the developed model was applied to analyse potential to recover cryogenic exergy of the Liquefied Natural Gas (LNG). The paper presents the results of the dimensional upscaling of the engine and the influence of the average working pressure. It was revealed that increasing the size of the engine or the average working pressure moves the engine to practically unachievable working conditions.

[1]  Somchai Wongwises,et al.  Thermodynamic analysis of a Stirling engine including dead volumes of hot space, cold space and regenerator , 2006 .

[2]  Wojciech Stanek,et al.  Application of the Stirling engine driven with cryogenic exergy of LNG (liquefied natural gas) for the production of electricity , 2016 .

[3]  Kai Wang,et al.  Stirling cycle engines for recovering low and moderate temperature heat: A review , 2016 .

[4]  Pascal Puech,et al.  Thermodynamic analysis of a Stirling engine including regenerator dead volume , 2011 .

[5]  A. Zmuda.  Estimation of the possibility of Stirling engine applications in LNG carrier power systems , 2010 .

[6]  Hoseyn Sayyaadi,et al.  CAFS: The Combined Adiabatic–Finite Speed thermal model for simulation and optimization of Stirling engines , 2015 .

[7]  Antonio Colmenar-Santos,et al.  Thermodynamic and exergoeconomic analysis of energy recovery system of biogas from a wastewater treatment plant and use in a Stirling engine , 2016 .

[8]  Daniela Chrenko,et al.  Zero dimensional finite-time thermodynamic, three zones numerical model of a generic Stirling and its experimental validation , 2012 .

[9]  Ali Reza Tavakolpour,et al.  Simulation, construction and testing of a two-cylinder solar Stirling engine powered by a flat-plate solar collector without regenerator , 2008 .

[10]  Moh’d A. Al-Nimr,et al.  Utilizing the heat rejected from a solar dish Stirling engine in potable water production , 2016 .

[11]  Charles Harman,et al.  Application of the Direct Method to irreversible Stirling cycles with finite speed , 2002 .

[12]  Somchai Wongwises,et al.  A review of solar-powered Stirling engines and low temperature differential Stirling engines , 2003 .

[13]  Somchai Wongwises,et al.  Investigation on power output of the gamma-configuration low temperature differential Stirling engines , 2005 .

[14]  H. G. Ladas,et al.  Finite-time view of the stirling engine , 1994 .

[15]  D. G. Thombare,et al.  TECHNOLOGICAL DEVELOPMENT IN THE STIRLING CYCLE ENGINES , 2008 .

[16]  Wojciech Stanek,et al.  Performance Analysis of the Small-Scale α-Type Stirling Engine Using Computational Fluid Dynamics Tools , 2018 .

[17]  F. Curzon,et al.  Efficiency of a Carnot engine at maximum power output , 1975 .

[18]  Daniela Chrenko,et al.  Simulation, experimental validation and kinematic optimization of a Stirling engine using air and helium , 2014 .

[19]  M. Babaelahi,et al.  A new thermal model based on polytropic numerical simulation of Stirling engines , 2015 .