Microstructure evolution and strengthening mechanisms of cold-drawn commercially pure aluminum wire

[1]  Shiteng Zhao,et al.  Influence of severe plastic deformation on dynamic strain aging of ultrafine grained Al–Mg alloys , 2014 .

[2]  Brandon D. Saller,et al.  Improving the tensile ductility and uniform elongation of high-strength ultrafine-grained Al alloys by lowering the grain boundary misorientation angle , 2014 .

[3]  Ruslan Z. Valiev,et al.  A nanostructural design to produce high-strength Al alloys with enhanced electrical conductivity , 2014 .

[4]  Julie M. Schoenung,et al.  Mechanical Behavior and Strengthening Mechanisms in Ultrafine Grain Precipitation-Strengthened Aluminum Alloy , 2014 .

[5]  I. Beyerlein,et al.  Microstructure, crystallographic texture, and plastic anisotropy evolution in an Mg alloy during equal channel angular extrusion processing , 2011 .

[6]  Qing Liu,et al.  Microstructure and strengthening mechanisms in cold-drawn pearlitic steel wire , 2011 .

[7]  W. Kim,et al.  Microstructure and mechanical properties of pure Ti processed by high-ratio differential speed rolling at room temperature , 2010 .

[8]  Z. Zhang,et al.  Tensile and low-cycle fatigue properties of Mg–2.8% Al–1.1% Zn–0.4% Mn alloy along the transverse and rolling directions , 2009 .

[9]  N. Gao,et al.  PREDICTING GRAIN REFINEMENT BY COLD SEVERE PLASTIC DEFORMATION IN ALLOYS USING VOLUME AVERAGED DISLOCATION GENERATION , 2009 .

[10]  I. Beyerlein,et al.  Texture evolution in equal-channel angular extrusion , 2009 .

[11]  H. Pirgazi,et al.  Microstructure evolution and mechanical properties of AA1100 aluminum sheet processed by accumulative roll bonding , 2008 .

[12]  Long-Sen Chang,et al.  Improvement of strength of magnesium alloy processed by equal channel angular extrusion , 2008 .

[13]  Z. G. Wang,et al.  Grain boundary effects on cyclic deformation and fatigue damage , 2008 .

[14]  J. C. Werenskiold,et al.  Dynamic precipitation during severe plastic deformation of an Al–Mg–Si aluminium alloy , 2008 .

[15]  Michael D. Uchic,et al.  Contribution to size effect of yield strength from the stochastics of dislocation source lengths in finite samples , 2007 .

[16]  I. Beyerlein,et al.  Plastic anisotropy in aluminum and copper pre-strained by equal channel angular extrusion , 2007 .

[17]  H. Maier,et al.  Mechanical flow anisotropy in severely deformed pure titanium , 2006 .

[18]  E. Pereloma,et al.  Microstructure and texture evolution of bcc and fcc metals subjected to equal channel angular extrusion , 2006 .

[19]  C. Davies,et al.  Deformation and texture evolution in AZ31 magnesium alloy during uniaxial loading , 2006 .

[20]  I. Beyerlein,et al.  Anisotropy in mechanical properties of high-purity copper processed by equal channel angular extrusion , 2005 .

[21]  R. Valiev,et al.  Microstructures and mechanical properties of ultrafine grained 7075 Al alloy processed by ECAP and their evolutions during annealing , 2004 .

[22]  W. D. Callister,et al.  Fundamentals of Materials Science and Engineering , 2004 .

[23]  Zujian Wang,et al.  Dependence of intergranular fatigue cracking on the interactions of persistent slip bands with grain boundaries , 2003 .

[24]  Xiaolei Wu,et al.  Microstructure and evolution of mechanically-induced ultrafine grain in surface layer of AL-alloy subjected to USSP , 2002 .

[25]  E. Starke,et al.  Effects of preferentially aligned precipitates on plastic anisotropy in Al-Cu-Mg-Ag and Al-Cu alloys , 1998 .

[26]  Z. Zhang,et al.  Effects of grain boundaries on cyclic deformation behavior of copper bicrystals and columnar crystals , 1998 .

[27]  J. E. Bailey,et al.  The dislocation distribution, flow stress, and stored energy in cold-worked polycrystalline silver , 1960 .