Cutting performance of nano-crystalline diamond (NCD) coating in micro-milling of Ti6Al4V alloy

Abstract Hard coatings are an important factor affecting the cutting performance of tools. In particular, they directly affect tool life, cutting forces, surface quality and burr formation in the micro-milling process. In this study, the performance of nano-crystalline diamond (NCD) coated tools was evaluated by comparing it with TiN-coated, AlCrN-coated and uncoated carbide tools in micro-milling of Ti 6 Al 4 V alloy. A series of micro-milling tests was carried out to determine the effects of coating type and machining conditions on tool wear, cutting force, surface roughness and burr size. Flat end-mill tools with two flutes and a diameter of 0.5 mm were used in the micro-milling process. The minimum chip thickness depending on both the cutting force and the surface roughness were determined. The results showed that the minimum chip thickness is about 0.3 times that of the cutter corner radius for Ti 6 Al 4 V alloy and changes very little with coating type. It was observed from wear tests that the dominant wear mechanism was abrasion. Maximum wear occurred on NCD-coated and uncoated tools. In addition, maximum burr size was obtained in the cutting process with the uncoated tool.

[1]  H. Tritschler,et al.  Micro cutting of steel , 2004 .

[2]  O. B. Ozdoganlar,et al.  An experimental investigation of micro-machinability of copper 101 using tungsten carbide micro-endmills , 2007 .

[3]  Paul Mativenga,et al.  Evaluation and selection of hard coatings for micro milling of hardened tool steel , 2008 .

[4]  A. Kumar,et al.  Micro milling of pure copper , 2001 .

[5]  Tuğrul Özel,et al.  Experimental and finite element simulation based investigations on micro-milling Ti-6Al-4V titanium alloy: Effects of cBN coating on tool wear , 2013 .

[6]  Yung C. Shin,et al.  Comparative evaluation of laser-assisted micro-milling for AISI 316, AISI 422, TI-6AL-4V and Inconel 718 in a side-cutting configuration , 2010 .

[7]  Giuliano Bissacco,et al.  Modelling the cutting edge radius size effect for force prediction in micro milling , 2008 .

[8]  István Mészáros,et al.  Micromilling of metallic materials , 2003 .

[9]  K. Aslantaş,et al.  An experimental investigation of the effect of coating material on tool wear in micro milling of Inconel 718 super alloy , 2013 .

[10]  J. Paulo Davim,et al.  Machining of titanium alloys , 2014 .

[11]  Chi Fai Cheung,et al.  A dynamic surface topography model for the prediction of nano-surface generation in ultra-precision machining , 2001 .

[12]  Fevzi Bedir,et al.  The performance Of DLC-coated and uncoated ultra-fine carbide tools in micromilling of Inconel 718 , 2015 .

[13]  Tony L. Schmitz,et al.  Runout effects in milling: Surface finish, surface location error, and stability , 2007 .

[14]  Richard E. DeVor,et al.  On the Modeling and Analysis of Machining Performance in Micro-Endmilling, Part I: Surface Generation , 2004 .

[15]  H. Weule,et al.  Micro-Cutting of Steel to Meet New Requirements in Miniaturization , 2001 .

[16]  Shih-Ming Wang,et al.  Development of micro milling force model and cutting parameter optimization , 2012 .

[17]  Dirk Biermann,et al.  Influence of cutting edge geometry and cutting edge radius on the stability of micromilling processes , 2009, Prod. Eng..

[18]  Adem Çiçek,et al.  Tool life and wear mechanism of coated and uncoated Al2O3/TiCN mixed ceramic tools in turning hardened alloy steel , 2012 .

[19]  L. Iuliano,et al.  Advanced coated ceramic tools for machining superalloys , 1997 .

[20]  B. Shen,et al.  Comparison of chemical vapor deposition diamond-, diamond-like carbon- and TiAlN-coated microdrills in graphite machining , 2013 .

[21]  Paul Mativenga,et al.  Size effect and tool geometry in micromilling of tool steel , 2009 .

[22]  Jin-Hyo Park,et al.  The characteristics of cutting forces in the micro-milling of AISI D2 steel , 2009 .

[23]  K. Aslantaş,et al.  The effect of minimum quantity lubrication and cryogenic pre-cooling on cutting performance in the micro milling of Inconel 718 , 2015 .

[24]  Robert W. Carpick,et al.  Analyzing the performance of diamond-coated micro end mills. , 2009 .

[25]  Giuliano Bissacco,et al.  Micromilling of hardened tool steel for mould making applications , 2005 .