Three-dimensional excimer laser micromachining using greyscale masks

Greyscale masks have been successfully implemented in an excimer laser micromachining system to produce structures with a continuous profile. During this work, it was found possible to machine structures to depths of several tens of microns with no observable mask degradation. The greyscale mask transmissions were defined using a matrix of pixels whose dimension was smaller than the resolution limit of the optical system in the laser micromachining system. By reduction-projecting the greyscale mask pattern onto the workpiece, the local fluence at the workpiece could be predetermined and hence the local machining rates controlled. This enabled three-dimensional (3D) structures to be fabricated at the workpiece in a single machining operation. Under the experimental conditions used in this investigation, the rate at which material was ablated was found to depend linearly on the percentage transmission of the mask. Various test structures, including complex 3D-contoured fluidic channels, have been produced.

[1]  Francis E. H. Tay,et al.  A novel micro-machining method for the fabrication of thick-film SU-8 embedded micro-channels , 2001 .

[2]  Cheng Sun,et al.  Micro-stereolithography of polymeric and ceramic microstructures , 1999 .

[3]  S. Zissi,et al.  Stereolithography and microtechniques , 1996 .

[4]  Dietmar Hirsch,et al.  Excimer laser machining for the fabrication of analogous microstructures , 1996 .

[5]  John F. Jarvis,et al.  A survey of techniques for the display of continuous tone pictures on bilevel displays , 1976 .

[6]  F. Bigl,et al.  Excimer laser micromachining and replication of 3D optical surfaces , 1998 .

[7]  Zheng Cui,et al.  Coding gray-tone mask for refractive microlens fabrication , 2000 .

[8]  E. Kley.  Continuous profile writing by electron and optical lithography , 1997 .

[9]  F. Bigl,et al.  Combination of contour and half-tone masks used in laser ablation , 2000 .

[10]  Zheng Cui,et al.  Refractive micro lens array made of dichromate gelatin with gray-tone photolithography , 2001 .

[11]  D R Purdy.  Fabrication of complex micro-optic components using photo-sculpting through halftone transmission masks , 1994 .

[12]  Alan G. R. Evans,et al.  Photoresist parabolas for curved micromirrors , 1998 .

[13]  Erol C. Harvey,et al.  Manufacture of miniature bioparticle electromanipulators by excimer laser ablation , 1998, Photonics West.

[14]  Hans Joachim Quenzer,et al.  One-level gray-tone design—mask data preparation and pattern transfer , 1996 .

[15]  J. Wengelink,et al.  Semitransparent mask technique for relief type surface topographies , 1995 .

[16]  Tarik Bourouina,et al.  Fabrication of a gray-tone mask and pattern transfer in thick photoresists , 1998 .

[17]  S. Zissi,et al.  Microstereophotolithography using a liquid crystal display as dynamic mask-generator , 1997 .

[18]  Erol C. Harvey,et al.  Excimer laser micromachining system for the production of bioparticle electromanipulation devices , 1997, Photonics West - Micro and Nano Fabricated Electromechanical and Optical Components.

[19]  Hans Joachim Quenzer,et al.  Microfabrication of complex surface topographies using grey-tone lithography , 1995 .

[20]  A. Braun,et al.  Diffractive gray scale masks for excimer laser ablation , 2002 .

[21]  Zheng Cui,et al.  Design of hybrid micro optical elements with coded gray-tone mask , 2001 .

[22]  Julian P.H. Burt,et al.  Fabrication of fluidic manifold systems using single-exposure grayscale masks , 2001, Microelectronic and MEMS Technologies.

[23]  Thomas Lippert,et al.  Diffractive grey-tone phase masks for laser ablation lithography , 2001 .

[24]  Sylvain Paineau,et al.  Multilevel diffractive optical element manufacture by excimer laser ablation and halftone masks , 2001, SPIE LASE.