Measurement of (post-)curing strain development with fibre Bragg gratings

Curing shrinkage of polymer matrices is a significant source of residual strain formation in thick composite products manufactured with liquid resin infusion. The goal of this paper is to investigate the contributions of cure shrinkage and postcure to residual strain development in a thermosetting polyurethane system suitable for resin infusion of thick composites using fibre Bragg gratings. The results showed that around half of the total shrinkage that contributes to residual strain build-up is due to chemical shrinkage, whereas the other half comprises thermal contraction from the vitrification point. The postcure treatment was found to relax internal strains significantly. The strain-free temperature was found below the postcure temperature and, therefore, the postcure treatment did not induce additional chemical or thermal strains.

[1]  A. Cusano,et al.  Chirped fiber-Bragg grating as self-temperature referenced strain sensor in nonisothermal thermoset processing , 2006, IEEE Sensors Journal.

[2]  Michael R Wisnom,et al.  In-situ measurement of chemical shrinkage of MY750 epoxy resin by a novel gravimetric method , 2004 .

[3]  Allan S. Crasto,et al.  On the Determination of Residual Stresses in Fiber-Reinforced Thermoset Composites , 1993 .

[4]  R. G. Reid,et al.  A novel method to measure residual stresses in unidirectional GFRP , 2009 .

[5]  Andrea Cusano,et al.  Cure-induced residual strain build-up in a thermoset resin , 2006 .

[6]  J. Karger‐Kocsis,et al.  Monitoring of cure‐induced strain of an epoxy resin by fiber Bragg grating sensor , 2008 .

[7]  Andrea Cusano,et al.  Advanced cure monitoring by optoelectronic multifunction sensing system , 2004 .

[8]  Changes in the thermomechanical behavior of epoxy glasses under the state of strain aging , 2008 .

[9]  Harald E.N. Bersee,et al.  Residual stresses in thermoplastic composites - a study of the literature. Part III: Effects of thermal residual stresses , 2007 .

[10]  Michael R Wisnom,et al.  Development of curvature during the cure of AS4/8552 [0/90] unsymmetric composite plates , 2003 .

[11]  Jacqueline I. Kroschwitz,et al.  Concise Encyclopedia of Polymer Science and Engineering , 1990 .

[12]  József Karger-Kocsis,et al.  Influence of Cure Regime on the Strain Development in an Epoxy Resin as Monitored by a Fiber Bragg Grating Sensor , 2007 .

[13]  Antonello Cutolo,et al.  Monitoring by a single fiber Bragg grating of the process induced chemo-physical transformations of a model thermoset , 2004 .

[14]  Terry Ford,et al.  High Performance Composites , 1993 .

[15]  Ralph P. Tatam,et al.  Thermal dependence of the strain response of optical fibre Bragg gratings , 2004 .

[16]  Andrea Cusano,et al.  Real time monitoring of cure and gelification of a thermoset matrix , 2006 .

[17]  John Botsis,et al.  Characterization of residual strains in an epoxy block using an embedded FBG sensor and the OLCR technique , 2006 .

[18]  W. Van Paepegem,et al.  Strain Monitoring in Thermoplastic Composites with Optical Fiber Sensors: Embedding Process, Visualization with Micro-tomography, and Fatigue Results , 2007 .

[19]  John Botsis,et al.  Characterisation of residual stresses in a single fibre composite with FBG sensor , 2007 .

[20]  Wim De Waele,et al.  Structural monitoring of composite elements using optical fibres with Bragg-sensors , 2002 .

[21]  K. Schoch,et al.  Real-time measurement of resin shrinkage during cure , 2004 .

[22]  K. Jansen.  Effect of resin formulation on thermoset viscoelasticity , 2006 .

[23]  Andrea Cusano,et al.  Non-isothermal monitoring of strain build-up in thermoset processing by a single chirped fiber Bragg grating , 2004, European Workshop on Optical Fibre Sensors.

[24]  Adriaan Beukers,et al.  Residual stresses in thermoplastic composites—A study of the literature—Part I: Formation of residual stresses , 2006 .