Study on contamination control in a minienvironment inside clean room for yield enhancement based on particle concentration measurement and airflow CFD simulation

A study was carried out to look for the source of contamination and examine the route of contaminant transfer in the minienvironment applied in LCD process clean room of Korea. As the minienvironment model, one of the clean room with much large space and low particle concentration was selected to investigate. Firstly, the particle concentrations were measured without any information on the source and the route of contaminants transfer. Through considering the results of particle measurements and CFD simulations simultaneously, however, it was revealed that the critical contamination source was the stocker and the contaminants were transferred by the airflow pattern in this study. As an improvement action, reducing the airflow rate of exhaust fans and installing additional fan filter units (FFUs) were carried out. As a result, the velocity distribution was improved and the particle concentration was reduced in the target minievironment. Also, the defect rate related to this minienvironment decreased. With the help of the experimental and the numerical tools, the effective method for contamination control was developed. Furthermore, this article provides recommendation for future work to improve the yield and save the energy consumption simultaneously.

[1]  Sheng-Bai Zhu,et al.  Study of airborne molecular contamination in minienvironments , 2002, 13th Annual IEEE/SEMI Advanced Semiconductor Manufacturing Conference. Advancing the Science and Technology of Semiconductor Manufacturing. ASMC 2002 (Cat. No.02CH37259).

[2]  Shih-Cheng Hu,et al.  Experimental study of airflow and particle characteristics of a 300-mm POUP/LPU minienvironment system , 2003 .

[3]  S. Patankar.  Numerical Heat Transfer and Fluid Flow , 2018, Lecture Notes in Mechanical Engineering.

[4]  Tengfang Xu,et al.  Performance of large fan-filter units for cleanroom applications , 2007 .

[5]  K.-C. Noh,et al.  Prediction and Evaluation of Cleanliness Levels Inside a Mini-Environment by Measuring Mean Air-Age and Effective Flow Rate , 2008, IEEE Transactions on Semiconductor Manufacturing.

[6]  Seung-Chul Lee,et al.  A numerical study on airflow and dynamic cross-contamination in the super cleanroom for photolithogr , 2005 .

[7]  Tengfang Xu,et al.  Characterization of minienvironments in a cleanroom: Assessing energy performance and its implications , 2008 .

[8]  A. Tannous.  Optimization of a Minienvironment Design Using Computational Fluid Dynamics , 2005 .

[9]  Liu Yang,et al.  Costing small cleanrooms , 2007 .

[10]  Shih-Cheng Hu,et al.  Simultaneous control of particle contamination and VOC pollution under different operating conditions of a mini-environment that contains a coating process , 2000 .

[11]  S. Kobayashi,et al.  Particle characteristics of 300-mm minienvironment (FOUP and LPU) , 2000 .

[12]  Huan-Ruei Shiu,et al.  Numerical simulation for air flow in the mini-environment and SMIF enclosure , 2003 .

[13]  Tengfang Xu,et al.  The development of fan filter unit with flow rate feedback control in a cleanroom , 2007 .

[14]  Tengfang Xu.  An Innovative Method for Dynamic Characterization of Fan Filter Unit Operation. , 2006 .

[15]  Tengfang Xu,et al.  Characterization of minienvironments in a clean room: Design characteristics and environmental performance , 2007 .

[16]  W. Whyte,et al.  Cleanroom Technology: Fundamentals of Design, Testing and Operation , 2001 .

[17]  Shih-Cheng Hu,et al.  Design and evaluation of a minienvironment for semiconductor manufacture processes , 2002 .

[18]  Chuen-Jinn Tsai,et al.  Simulation and testing of pollutant dispersion during preventive maintenance in a cleanroom , 2009 .

[19]  Tengfang Xu,et al.  A Study on the Operation Performance of a Minienvironment System , 2006 .