Micromechanical analysis of yielding of metal matrix composites

Abstract A recently proposed micromechanics model is employed to generate initial yield surfaces of unidirectional and cross-ply metal matrix composites under a variety of loading conditions. The yield surfaces are calculated using two different methodologies: on the basis of local matrix stresses and average stresses in the entire matrix phase. It is shown that the results obtained on the basis of local matrix stresses correlate very well with finite-element predictions for most loading directions considered in the present investigation. A critical direction or cone of directions is found that should be avoided with the outlined micromechanics model. This direction corresponds to a particular combination of longitudinal tension (compression) and equal biaxial transverse tension (compression) whose ratio is a function of the constituent properties. It is also illustrated that the results generated on the basis of average matrix stresses generally underestimate initial yielding (i.e., predict higher yield stresses), the extent of which may be significant depending on the direction of loading. Thus, the use of average matrix stresses in analyzing elastoplastic response of composites should be approached with caution.

[1]  Raymond L. Foye,et al.  Theoretical Post-Yielding Behavior of Composite Laminates Part II-Inelastic Macromechanics , 1973 .

[2]  T. Lin,et al.  Elastic-Plastic Analysis of Unidirectional Composites , 1972 .

[3]  R. Hill.  Elastic properties of reinforced solids: some theoretical principles , 1963 .

[4]  G. Dvorak,et al.  Plasticity Analysis of Fibrous Composites , 1982 .

[5]  G. Dvorak,et al.  Axisymmetric plasticity theory of fibrous composites , 1976 .

[6]  D. Salinas,et al.  Initial Yield Surface of a Unidirectionally Reinforced Composite , 1972 .

[7]  Jacob Aboudi,et al.  Effective behavior of inelastic fiber-reinforced composites , 1984 .

[8]  J. Aboudi.  The effective thermomechanical behavior of inelastic fiber-reinforced materials , 1985 .

[9]  Jacob Aboudi,et al.  Closed form constitutive equations for metal matrix composites , 1987 .

[10]  Jacob Aboudi,et al.  Elastoplasticity theory for composite materials , 1986 .

[11]  G. J. Dvorak,et al.  Generalized Initial Yield Surfaces for Unidirectional Composites , 1974 .

[12]  T. G. Rogers,et al.  Cyclic Extension of an Elastic Fibre with an Elastic-plastic Coating , 1967 .

[13]  T. Mori,et al.  Plastic deformation anisotropy and work-hardening of composite materials , 1973 .

[14]  George J. Dvorak,et al.  Thermal Stresses in Heat-Treated Fibrous Composites , 1976 .

[15]  S. R. Bodner,et al.  Constitutive Equations for Elastic-Viscoplastic Strain-Hardening Materials , 1975 .

[16]  Elastoplastic Transverse Properties of a Unidirectional Fibre Reinforced Composite , 1973 .

[17]  Rodney Hill,et al.  Theory of mechanical properties of fibre-strengthened materials: I. Elastic behaviour , 1964 .

[18]  Rodney Hill,et al.  Theory of mechanical properties of fibre-strengthened materials—III. self-consistent model , 1965 .

[19]  Donald F. Adams,et al.  Inelastic Analysis of a Unidirectional Composite Subjected to Transverse Normal Loading , 1970 .

[20]  B. W. Shaffer.  Elastic-plastic stress distribution within reinforced plastics loaded normal to its internal filaments. , 1968 .

[21]  George J. Dvorak,et al.  Elastic-plastic behavior of fibrous composites , 1979 .

[22]  M. Pindera,et al.  Influence of stress interaction on the behavior of off-axis unidirectional composites , 1982 .

[23]  M. S. Madhava Rao,et al.  Yielding in Unidirectional Composites Under External Loads and Temperature Changes* , 1973 .

[24]  S. Umekawa,et al.  A Micromechanical Prediction of Initial Yield Surfaces of Unidirectional Composites , 1979 .