Cryogenic machining of porous tungsten for enhanced surface integrity

Abstract Cryogenic machining of porous tungsten is being developed as an alternative sustainable process to current industry practice of machining plastic infiltrated workpieces. Eliminating the use of plastic infiltrant is contingent on the ability to control as-machined surface properties of porous tungsten. To this end, the influence of various machining parameters and cooling conditions on machining mechanisms, particularly as a function of cutting temperature, is explored. By employing modified polycrystalline diamond cutting tools, high speed cryogenic machining of porous tungsten by ductile shear was achieved. Cutting speeds of up to 400 m/min are possible with this novel approach, and very low surface roughness of Ra ≈ 0.4 μm is realized, at the expense of surface porosity. At low cutting speeds, rake angle has a key impact on surface morphology, with more negative rake angles increasing the amount of brittle fracture occurring on the machined surface and thereby increasing surface porosity. An excellent mix of open surface porosity and low surface roughness may be achieved at low cutting speeds of 20 m/min when a sharp edged cutting tool with a rake angle of −5° is used. Using a separate set of machining parameters for rough and finish machining may offer an optimum approach to realize economical cryogenic machining of porous tungsten.

[1]  E. Alizadeh.  Factors influencing the machinability of sintered steels , 2008 .

[2]  D. Umbrello,et al.  The effects of cryogenic cooling on surface integrity in hard machining: A comparison with dry machining , 2011 .

[3]  Zh. I. Dzneladze,et al.  Variation of the open and closed porosity of porous tungsten during sintering , 1977 .

[4]  I. S. Jawahir,et al.  Increased Surface Integrity in Porous Tungsten from Cryogenic Machining with Cermet Cutting Tool , 2016 .

[5]  Masahiro Higuchi,et al.  Mechanism of Cutting Edge Chipping and Its Suppression in Diamond Turning of Copper , 2005 .

[6]  Z. Y. Wang,et al.  Cryogenic machining of hard-to-cut materials , 2000 .

[7]  J. L Cronin,et al.  Modern dispenser cathodes , 1981 .

[8]  S. Palanisamy,et al.  Effect of cryogenic compressed air on the evolution of cutting force and tool wear during machining of Ti-6Al-4V alloy , 2015 .

[9]  I. Jawahir,et al.  Cryogenic machining of porous tungsten for dispenser cathode applications , 2008, 2008 IEEE International Vacuum Electronics Conference.

[10]  R. Ghosh,et al.  FINISH-TURNING OF HARDENED POWDER-METALLURGY STEEL USING CRYOGENIC COOLING , 2003 .

[11]  A. Wronski,et al.  The effects of strain rate and pressurization on the ductile-brittle transition temperature of polycrystalline sintered tungsten , 1969 .

[12]  A. Wronski,et al.  The ductile-brittle transition in polycrystalline tungsten , 1965 .

[13]  I. Jawahir,et al.  Improved Product Quality and Resource Efficiency in Porous Tungsten Machining for Dispenser Cathode Application by Elimination of the Infiltration Process , 2013 .

[14]  E. Bordatchev,et al.  Porosity and cutting forces: from macroscale to microscale machining correlations , 2011 .

[15]  I. S. Jawahir,et al.  The effects of progressive tool wear and tool restricted contact on chip breakability in machining , 1993 .

[16]  Volker Schulze,et al.  Study on micro texturing of uncoated cemented carbide cutting tools for wear improvement and built-up edge stabilisation , 2015 .

[17]  A. Giannattasio,et al.  Strain-rate dependence of the brittle-to-ductile transition temperature in tungsten , 2007 .

[18]  V. V. Skorokhod,et al.  Correlation between the particle size, pore size, and porous structure of sintered tungsten , 1988 .

[19]  A. Wronski,et al.  SLIP-INDUCED CLEAVAGE IN POLYCRYSTALLINE TUNGSTEN , 1964 .

[20]  I. Jawahir,et al.  Observations on cutting edge radius effects in cryogenic machining of porous tungsten , 2015, 2015 IEEE International Vacuum Electronics Conference (IVEC).