Rapid mapping and analysing rock mass discontinuities with 3D terrestrial laser scanning in the underground excavation

Abstract Whilst laser scanning techniques have been shown to facilitate rapid identification and analysis of rock mass characteristics, relatively little research has been conducted for 3D laser scanning in underground spaces. In the present study, a semi-automatic laser scanning method has been presented for non-contact discontinuity identification and rock mass characterisation in a Western Australian underground gold mine. The accuracy of the 3D laser scanning technique was compared with traditional window mapping with a strong correlation being noted. The average dip/dip direction discrepancy between the two methods was found to be 1.5°/16° and attributed to the ability of 3D laser scanning to collect significant quantities of data when compared to traditional methods. Potential sources of error, together with the influence of the scale effect, were discussed with an optimum scanning resolution of 7.5 mm at 5 m being noted to provide a combination of significantly reduced collection and processing time and high levels of accuracy. Overall, the present study demonstrated the potential of 3D laser scanning techniques to replace traditional methods with increased efficiency and accuracy in underground mines.

[1]  Nick Barton,et al.  Engineering classification of rock masses for the design of tunnel support , 1974 .

[2]  Adrián J. Riquelme,et al.  A new approach for semi-automatic rock mass joints recognition from 3D point clouds , 2014, Comput. Geosci..

[3]  John A. Franklin,et al.  Rock mass characterization using photoanalysis , 1988 .

[4]  Denis Thibodeau,et al.  3D laser imaging for surface roughness analysis , 2013 .

[5]  Qihu Qian,et al.  Safety risk management of underground engineering in China: Progress, challenges and strategies , 2016 .

[6]  P. Grussenmeyer,et al.  Surveying and modeling of rock discontinuities by terrestrial laser scanning and photogrammetry: Semi-automatic approaches for linear outcrop inspection , 2014 .

[7]  S. Buckley,et al.  Terrestrial laser scanning in geology: data acquisition, processing and accuracy considerations , 2008, Journal of the Geological Society.

[8]  S. Slob.  Automated rock mass characterisation using 3-D terrestrial laser scanning , 2010 .

[9]  R. D. Terzaghi.  Sources of Error in Joint Surveys , 1965 .

[10]  D. J. Hutchinson,et al.  Bias Correction for View-limited Lidar Scanning of Rock Outcrops for Structural Characterization , 2010 .

[11]  Mark S. Diederichs,et al.  Optimization of LiDAR scanning and processing for automated structural evaluation of discontinuities in rockmasses , 2009 .

[12]  Piotr Zagórski,et al.  Use of terrestrial laser scanning (TLS) for monitoring and modelling of geomorphic processes and phenomena at a small and medium spatial scale in Polar environment (Scott River — Spitsbergen) , 2014 .

[13]  Mark S. Diederichs,et al.  Integration of three-dimensional laser scanning with discontinuum modelling for stability analysis of tunnels in blocky rockmasses , 2013 .

[14]  Ming Cai,et al.  Visualization of rock mass classification systems , 2006 .

[15]  Z. Bieniawski.  Determining rock mass deformability: experience from case histories , 1978 .

[16]  Nicola Casagli,et al.  Semi-automatic extraction of rock mass structural data from high resolution LIDAR point clouds , 2011 .

[17]  Mark S. Diederichs,et al.  Geotechnical and operational applications for 3-dimensional laser scanning in drill and blast tunnels , 2010 .

[18]  Santiago Martín,et al.  Construction of accurate geological cross-sections along trenches, cliffs and mountain slopes using photogrammetry , 2013, Comput. Geosci..

[19]  Håkan Stille,et al.  Ground behaviour and rock mass composition in underground excavations , 2008 .

[20]  Hongyuan Liu,et al.  Experimental study on failure behaviour of deep tunnels under high in-situ stresses , 2015 .

[21]  Mark S. Diederichs,et al.  Automated rockmass discontinuity mapping from 3-dimensional surface data , 2013 .

[22]  Matthew J. Lato,et al.  Rock bench: Establishing a common repository and standards for assessing rockmass characteristics using LiDAR and photogrammetry , 2013, Comput. Geosci..

[23]  Thomas P. Kersten,et al.  Methods for Geometric Accuracy Investigations of Terrestrial Laser Scanning Systems , 2009 .

[24]  Jinge Wang,et al.  A Description for Rock Joint Roughness Based on Terrestrial Laser Scanner and Image Analysis , 2015, Scientific Reports.

[25]  Stephen D. McKinnon,et al.  3D laser imaging for joint orientation analysis , 2011 .

[26]  D. Stead,et al.  Close-range terrestrial digital photogrammetry and terrestrial laser scanning for discontinuity characterization on rock cuts , 2009 .

[27]  T. R. Reid,et al.  A semi-automated methodology for discontinuity trace detection in digital images of rock mass exposures , 2000 .

[28]  A. Abellán,et al.  Discontinuity spacing analysis in rock masses using 3D point clouds , 2015 .

[29]  Deodato Tapete,et al.  Terrestrial laser scanning for rockfall stability analysis in the cultural heritage site of Pitigliano (Italy) , 2013, Landslides.

[30]  Gianfranco Forlani,et al.  Advanced Geostructural Survey Methods Applied to Rock Mass Characterization , 2009 .

[31]  E. Hoek,et al.  The geological strength index: applications and limitations , 2005 .

[32]  Gessica Umili,et al.  A new method for automatic discontinuity traces sampling on rock mass 3D model , 2012, Comput. Geosci..

[33]  F. Donze,et al.  Modelling progressive failure in fractured rock masses using a 3D discrete element method , 2012 .

[34]  S. Priest,et al.  ESTIMATION OF DISCONTINUITY SPACING AND TRACE LENGTH USING SCANLINE SURVEYS , 1981 .