Computations of flow and heat transfer in a three-dimensional multilouvered fin geometry

Abstract This study presents computational results in a complex three-dimensional louver geometry. The three-dimensionality occurs along the height of the fin, where the angled louver transitions to the flat landing and joins with the tube surface. The transition region is characterized by a swept leading edge and decreasing flow area between louvers. The results show that for Re b =1100, the flow on the angled louver is dominated by spanwise vortex shedding, which is weakly three-dimensional. On the other hand, the flow in the transition region exhibits strong three-dimensionality. A high-energy compact vortex jet forms in the vicinity of the louver junction with the flat landing and is drawn under the louver. The top surface experiences large velocities in the vicinity of the surface and exhibits high heat transfer coefficients. Although the flow slows down at the flat landing, the large induced velocities on the top surface increases the heat transfer coefficient on the tube surface.

[1]  E. Sparrow,et al.  Fully Developed Flow and Heat Transfer in Ducts Having Streamwise-Periodic Variations of Cross-Sectional Area , 1977 .

[2]  Jinhee Jeong,et al.  On the identification of a vortex , 1995, Journal of Fluid Mechanics.

[3]  Danesh K. Tafti,et al.  Time-dependent calculation procedure for fully developed and developing flow and heat transfer in louvered fin geometries , 1999 .

[4]  S. Balachandar,et al.  Computations of flow and heat transfer in parallel-plate fin heat exchangers on the CM-5: effects of flow unsteadiness and three-dimensionality , 1997 .

[5]  S. Balachandar,et al.  Low-frequency unsteadiness in the wake of a normal flat plate , 1997, Journal of Fluid Mechanics.

[6]  EFFECTS OF INTRINSIC THREE DIMENSIONALITY ON HEAT TRANSFER AND FRICTION LOSS IN A PERIODIC ARRAY OF PARALLEL PLATES , 1997 .

[7]  F. Beauvais.  An Aerodynamic Look at Automotive Radiators , 1965 .

[8]  Chi-Chuan Wang,et al.  A generalized heat transfer correlation for Iouver fin geometry , 1997 .

[9]  Suhas V. Patankar,et al.  An analysis of the effect of plate thickness on laminar flow and heat transfer in interrupted-plate passages , 1981 .

[10]  D. Tafti,et al.  Geometry effects on flow transition in multilouvered fins – onset, propagation, and characteristic frequencies , 2001 .

[11]  D. Tafti,et al.  Large-Eddy Simulations of Flow and Heat Transfer in Complex Three-Dimensional Multilouvered Fins , 2000 .

[12]  Naim Afgan,et al.  Heat Exchangers Theory Amp Practice , 1983 .

[13]  Balachandar,et al.  Generation of streamwise vortical structures in bluff body wakes. , 1995, Physical review letters.

[14]  Danesh K. Tafti,et al.  Flow transition in a multilouvered fin array , 2000 .

[15]  S. Balachandar,et al.  Autogeneration of near-wall vortical structures in channel flow , 1996 .

[16]  D. Tafti,et al.  Classification and effects of thermal wakes on heat transfer in multilouvered fins , 2001 .

[17]  E. Sparrow,et al.  Measurements of heat transfer and pressure drop for an array of staggered plates aligned parallel to an air flow , 1980 .

[18]  M. S. Chong,et al.  A general classification of three-dimensional flow fields , 1990 .

[19]  R. Webb,et al.  Condensate drainage and retention in louver fin automotive evaporators , 2000 .

[20]  S. Balachandar,et al.  Heat transfer enhancement mechanisms in inline and staggered parallel-plate fin heat exchangers , 1997 .

[21]  C. J. Davenport.  Heat Transfer and Flow Friction Characteristics of Louvred Heat Exchanger Surfaces , 1981 .

[22]  Ralph L. Webb,et al.  How structure in the louvered fin heat exchanger geometry , 1991 .

[23]  P. Moin,et al.  Application of a Fractional-Step Method to Incompressible Navier-Stokes Equations , 1984 .