TMF panel tests: close-to-reality simulation of thermo-mechanical fatigue processes in heat-loaded walls

The concept of a Thermo-Mechanical Fatigue (TMF) - test bench is discussed in this paper. Motivation for the TMF tests are two-fold: to assess the life expectation of structures being exposed to extreme thermo-mechanical loads first on subcomponent or panel level, and to serve as validation experiment for life-prediction models. In Europe, the concept of TMF-panel testing was first very successfully applied to rocket thrust chamber structures in the frame of the Ariane 5 Flight Recovery Programme in 2003 and 2004. These encouraging results have motivated the partners DLR Lampoldshausen and EADS Astrium to jointly investigate again the TMF-bench concept with special focus on meeting relevant requirements for future liquid propulsion needs. The following key elements of a TMF test bench are presented in the paper: the TMF heating device - a diode Laser, the panel housing, the fluid, measurement and control systems as well as the tentative design of a combustion chamber type TMF panel. Furthermore, numerical analyses of this tentative TMF panel – such as a CFD as well as a thermal and structural Finite Element analysis of the core part of the TMF panel during the Laser loading are shown.

[1]  Marion Bartsch,et al.  Temperature Measurement in Thermal Gradient Mechanical Fatigue Testing of Material Systems with Coatings , 2002 .

[2]  Björn Laumert,et al.  Redesign of the Vulcain 2 Nozzle Extension , 2005 .

[3]  Andreas Gernoth,et al.  TMF: Laser Application for a Close-to-Reality Simulation of Thermo-Mechanical Fatigue Processes in Rocket Engines , 2007 .

[4]  Tomas Damgaard,et al.  The V2+ Nozzle Extension Demo: A milestone on the route to sandwich nozzle production. , 2006 .

[5]  Bernd Köhler,et al.  11-kW direct diode laser system with homogenized 55 × 20 mm2 Top-Hat intensity distribution , 2007, SPIE LASE.

[6]  Michael Oschwald,et al.  Experimental and Numerical Investigations of Thermal Stratification Effects , 2003 .

[7]  Jörg Riccius,et al.  Material damage induced by environment and temperature and identification process , 2004 .

[8]  Hans Immich,et al.  Thrust Chamber Technology Developments for Future Launch Vehicle Liquid Rocket Engines , 2001 .

[9]  J. Riccius,et al.  Elasto-plastic and fatigue tests of a typical combustion chamber material with different sample geometries , 2002 .

[10]  Jörg Riccius,et al.  DETERMINATION OF LINEAR AND NONLINEAR PARAMETERS OF COMBUSTION CHAMBER WALL MATERIALS , 2003 .

[11]  Evgeny Zametaev,et al.  Influence of Time Dependent Effects on the Estimated Life Time of Liquid Rocket Combustion Chamber Walls , 2004 .

[12]  Christian Coddet,et al.  Vacuum Plasma Spray Process Applied to High Thickness Components for LRE , 2005 .

[13]  Jörg Riccius,et al.  Comparison of 2d and 3d Structural FE-Analyses of LRE Combustion Chamber Walls , 2006 .

[14]  Tomas Damgaard,et al.  Demonstration of a Laser Welded Channel Wall Nozzle - Vulcain 2 Scale , 2006 .

[15]  Marion Bartsch,et al.  CMSX-4 with Thermal Barrier Coating under Thermal Gradient Mechanical Fatigue , 2006 .

[16]  Michael Terhardt,et al.  Vulcain 2 Nozzle Extension: Integrated European Team and Advanced Computational Model to the Service of Nozzle Design , 2005 .

[17]  Michael Oschwald,et al.  Test Specimen Design and Measurement Technique for Investigation of Heat Transfer Processes in Cooling Channels of Rocket Engines under Real Thermal Conditions , 2003 .

[18]  Gerald Hagemann,et al.  Technology Efforts Towards Low-Cost Thrust Chambers , 2003 .