Fabrication and characteristic analysis of a poly(propylene fumarate) scaffold using micro-stereolithography technology.

Scaffold fabrication for regenerating functional human tissues has an important role in tissue engineering, and there has been much progress in research on scaffold fabrication. However, current methods are limited by the mechanical properties of existing biodegradable materials and the irregular structures that they produce. Recently, several promising biodegradable materials have been introduced, including poly(propylene fumarate) (PPF). The development of micro-stereolithography allows the fabrication of free-form 3D microstructures as designed. Since this technology requires a low-viscosity resin to fabricate fine structures, we reduced the viscosity of PPF by adding diethyl fumarate. Using our system, the curing characteristics and material properties of the resin were analyzed experimentally. Then, we fabricated waffle shape and 3D scaffolds containing several hundred regular micro pores. This method controlled the pore size, porosity, interconnectivity, and pore distribution. The results show that micro-stereolithography has big advantages over conventional fabrication methods. In addition, the ultimate strength and elastic modulus of the fabricated scaffolds were measured, and cell adhesion to the fabricated scaffold was observed by growing seeded cells on it. These results showed that the PPF/DEF scaffold is a potential bone scaffold for tissue engineering.

[1]  R L Reis,et al.  A new approach based on injection moulding to produce biodegradable starch-based polymeric scaffolds: morphology, mechanical and degradation behaviour. , 2001, Biomaterials.

[2]  E. D. Rekow,et al.  Engineered cellular response to scaffold architecture in a rabbit trephine defect. , 2003, Journal of biomedical materials research. Part A.

[3]  J. Lewis,et al.  Microperiodic structures: Direct writing of three-dimensional webs , 2004, Nature.

[4]  E. D. Rekow,et al.  Performance of degradable composite bone repair products made via three-dimensional fabrication techniques. , 2003, Journal of biomedical materials research. Part A.

[5]  D E Ingber,et al.  Preparation of poly(glycolic acid) bonded fiber structures for cell attachment and transplantation. , 1993, Journal of biomedical materials research.

[6]  J. Fisher,et al.  Photocrosslinking characteristics and mechanical properties of diethyl fumarate/poly(propylene fumarate) biomaterials. , 2002, Biomaterials.

[7]  A. Mikos,et al.  Injectable biodegradable materials for orthopedic tissue engineering. , 2000, Biomaterials.

[8]  Dong-Woo Cho,et al.  Development of an Assembly-free Process Based on Virtual Environment for Fabricating 3D Microfluidic Systems Using Microstereolithography Technology , 2004 .

[9]  Scott J Hollister,et al.  Mechanical and in vivo performance of hydroxyapatite implants with controlled architectures. , 2002, Biomaterials.

[10]  Etienne Burdet,et al.  Microrobotics and MEMS-based fabrication techniques for scaffold-based tissue engineering. , 2005, Macromolecular bioscience.

[11]  J. Lewis,et al.  Concentrated hydroxyapatite inks for direct-write assembly of 3-D periodic scaffolds. , 2005, Biomaterials.

[12]  R Langer,et al.  Laminated three-dimensional biodegradable foams for use in tissue engineering. , 1993, Biomaterials.

[13]  Chee Kai Chua,et al.  Development of a Tissue Engineering Scaffold Structure Library for Rapid Prototyping. Part 1: Investigation and Classification , 2003 .

[14]  R. Langer,et al.  Selected advances in drug delivery and tissue engineering. , 1999, Journal of controlled release : official journal of the Controlled Release Society.

[15]  W. Hayes,et al.  Ex vivo degradation of a poly(propylene glycol-fumarate) biodegradable particulate composite bone cement. , 1997, Journal of biomedical materials research.

[16]  E. D. Rekow,et al.  Performance of hydroxyapatite bone repair scaffolds created via three-dimensional fabrication techniques. , 2003, Journal of biomedical materials research. Part A.

[17]  Robert Langer,et al.  Preparation and characterization of poly(l-lactic acid) foams , 1994 .

[18]  I. Zein,et al.  Fused deposition modeling of novel scaffold architectures for tissue engineering applications. , 2002, Biomaterials.

[19]  A. L. Oliveira,et al.  Surface modification tailors the characteristics of biomimetic coatings nucleated on starch-based polymers , 1999, Journal of materials science. Materials in medicine.

[20]  J M Powers,et al.  Fabrication of biodegradable polymer scaffolds to engineer trabecular bone. , 1995, Journal of biomaterials science. Polymer edition.

[21]  E. D. Rekow,et al.  In vivo bone response to 3D periodic hydroxyapatite scaffolds assembled by direct ink writing. , 2007, Journal of biomedical materials research. Part A.

[22]  T Ushida,et al.  A biodegradable hybrid sponge nested with collagen microsponges. , 2000, Journal of biomedical materials research.

[23]  A. Mikos,et al.  The Importance of New Processing Techniques in Tissue Engineering , 1996, MRS bulletin.

[24]  R Langer,et al.  Novel approach to fabricate porous sponges of poly(D,L-lactic-co-glycolic acid) without the use of organic solvents. , 1996, Biomaterials.

[25]  A. Mikos,et al.  Injectable biodegradable polymer composites based on poly(propylene fumarate) crosslinked with poly(ethylene glycol)-dimethacrylate. , 2000, Biomaterials.

[26]  Kyriacos A. Athanasiou,et al.  Biodegradable PLA-PGA Polymers for Tissue Engineering in Orthopaedics , 1997 .

[27]  Malcolm N. Cooke,et al.  Use of stereolithography to manufacture critical-sized 3D biodegradable scaffolds for bone ingrowth. , 2003, Journal of biomedical materials research. Part B, Applied biomaterials.