Development of a Latchable Microvalve Employing a Low-Melting-Temperature Metal Alloy

We present the design, fabrication, and characterization of a latchable microvalve. The valve can be held in the on- or off-state without consuming power. A low-melting-temperature metal alloy provides structural support to hold the valve in place when latched. The metal alloy piece liquefies when it is heated above 62degC, allowing a pneumatic actuator to change the valve state. When the metal cools and solidifies, the valve is once again latched. This type of valve may be useful for portable lab-on-a-chip devices that require low-power operation and long-term fluid storage. A thin-film metal heater has been integrated into the polydimethylsiloxane device to provide localized heating for individual valve elements. Valve closing and opening response times have been simulated and verified by experiment. The burst pressure has been experimentally characterized and parameters influencing this burst pressure have been modeled.

[1]  M. Capanu,et al.  Design, fabrication, and testing of a bistable electromagnetically actuated microvalve , 2000, Journal of Microelectromechanical Systems.

[2]  S. Quake,et al.  Monolithic microfabricated valves and pumps by multilayer soft lithography. , 2000, Science.

[3]  Kee Suk Ryu,et al.  A modular microfluidic architecture for integrated biochemical analysis. , 2005, Proceedings of the National Academy of Sciences of the United States of America.

[4]  W. Menz,et al.  Microvalves with bistable buckled polymer diaphragms , 1996 .

[5]  Chang Liu,et al.  A Bi-Stable Latchable PDMS Valve Employing Low Melting Temperature Metal Alloys , 2007, TRANSDUCERS 2007 - 2007 International Solid-State Sensors, Actuators and Microsystems Conference.

[6]  R. Pal,et al.  Phase change microvalve for integrated devices. , 2004, Analytical chemistry.

[7]  Yves H. Berthelot,et al.  CMOS compatible bistable electromagnetic microvalve on a single wafer , 2005, Microelectron. J..

[8]  Werner Karl Schomburg,et al.  Design optimization of bistable microdiaphragm valves , 1998 .

[9]  Bozhi Yang,et al.  A latchable microvalve using phase change of paraffin wax , 2007 .

[10]  Jun Xie,et al.  Surface micromachined electrostatically actuated micro peristaltic pump. , 2004, Lab on a chip.

[11]  T. Abe,et al.  A proportional microvalve using a bi-stable magnetic actuator , 1997, Proceedings IEEE The Tenth Annual International Workshop on Micro Electro Mechanical Systems. An Investigation of Micro Structures, Sensors, Actuators, Machines and Robots.

[12]  M. Mehregany,et al.  Latched valve manifolds for efficient control of pneumatically actuated valve arrays , 1997, Proceedings of International Solid State Sensors and Actuators Conference (Transducers '97).

[13]  W. M. Haynes.  CRC Handbook of Chemistry and Physics , 1990 .

[14]  Werner Karl Schomburg,et al.  Polymer micro valve with a hydraulic piezo-drive fabricated by the AMANDA process , 2004 .

[15]  Makoto Ishida,et al.  A MEMS microvalve with PDMS diaphragm and two-chamber configuration of thermo-pneumatic actuator for integrated blood test system on silicon , 2005 .

[16]  William H. Grover,et al.  Development and multiplexed control of latching pneumatic valves using microfluidic logical structures. , 2006, Lab on a chip.

[17]  G. Whitesides,et al.  Torque-actuated valves for microfluidics. , 2005, Analytical chemistry.

[18]  K. Wise,et al.  An electrostatically latching thermopneumatic microvalve with closed-loop position sensing , 2005, 18th IEEE International Conference on Micro Electro Mechanical Systems, 2005. MEMS 2005..

[19]  Wolfgang Benecke,et al.  Microfluidic system for the integration and cyclic operation of gas sensors , 1999 .

[20]  Y. Tai,et al.  Design, fabrication, and testing of micromachined silicone rubber membrane valves , 1999 .

[21]  Bernhard Wagner,et al.  A Bistable Pneumatic Microswitch For Driving Fluidic Components , 1995, Proceedings of the International Solid-State Sensors and Actuators Conference - TRANSDUCERS '95.

[22]  J. Mueller,et al.  Leak-tight piezoelectric microvalve for high-pressure gas micropropulsion , 2004, Journal of Microelectromechanical Systems.

[23]  S. Quake,et al.  Microfluidic Large-Scale Integration , 2002, Science.

[24]  H. B. Halsall,et al.  Development and Characterization of Microfluidic Devices and Systems for Magnetic Bead-Based Biochemical Detection , 2001 .

[25]  U. Ghoshal,et al.  Cooling of high-power-density microdevices using liquid metal coolants , 2004 .

[26]  Chong H. Ahn,et al.  Institute of Physics Publishing Journal of Micromechanics and Microengineering a Review of Microvalves , 2022 .

[27]  Kensall D. Wise,et al.  A low pressure micromachined flow modulator , 1998 .

[28]  William H. Grover,et al.  Monolithic membrane valves and diaphragm pumps for practical large-scale integration into glass microfluidic devices , 2003 .

[29]  M. T. Korthorst,et al.  A micromachined silicon valve driven by a miniature bi-stable electro-magnetic actuator , 2000 .

[30]  D. Erickson,et al.  Joule heating and heat transfer in poly(dimethylsiloxane) microfluidic systems. , 2003, Lab on a chip.