Analysis and Comparison of a Fast Turn-On Series IGBT Stack and High-Voltage-Rated Commercial IGBTS

High-voltage-rated solid-state switches such as insulated-gate bipolar transistors (IGBTs) are commercially available up to 6.5 kV. Such voltage ratings are attractive for pulsed power and high-voltage switch-mode converter applications. However, as the IGBT voltage ratings increase, the rate of current rise and fall are generally reduced. This tradeoff is difficult to avoid as IGBTs must maintain a low resistance in the epitaxial or drift region layer. For high-voltage-rated IGBTs with thick drift regions to support the reverse voltage, the required high carrier concentrations are injected at turn on and removed at turn off, which slows the switching speed. An option for faster switching is to series multiple, lower voltage-rated IGBTs. An IGBT-stack prototype with six, 1200 V rated IGBTs in series has been experimentally tested. The six-series IGBT stack consists of individual, optically isolated, gate drivers and aluminum cooling plates for forced air cooling which results in a compact package. Each IGBT is overvoltage protected by transient voltage suppressors. The turn-on current rise time of the six-series IGBT stack and a single 6.5 kV rated IGBT has been experimentally measured in a pulsed resistive-load, capacitor discharge circuit. The IGBT stack has also been compared to two IGBT modules in series, each rated at 3.3 kV, in a boost circuit application switching at 9 kHz and producing an output of 5 kV. The six-series IGBT stack results in improved turn-on switching speed, and significantly higher power boost converter efficiency due to a reduced current tail during turn off. The experimental test parameters and the results of the comparison tests are discussed in the following paper

[1]  G. G. Stokes.  "J." , 1890, The New Yale Book of Quotations.

[2]  T. Undeland,et al.  IGBT turn-off losses for hard switching and with capacitive snubbers , 1991, Conference Record of the 1991 IEEE Industry Applications Society Annual Meeting.

[3]  Patrick R. Palmer,et al.  A comparison of IGBT technologies for use in the series connection , 1996 .

[4]  Juli Yamashita,et al.  A relation between dynamic saturation characteristics and tail current of nonpunchthrough IGBT , 1996, IAS '96. Conference Record of the 1996 IEEE Industry Applications Conference Thirty-First IAS Annual Meeting.

[5]  Y. Tomomatsu,et al.  High Voltage IGBT(HV-IGBT) having p'/p' collector region , 1998 .

[6]  Salvatore Musumeci,et al.  Control of the switching transients of IGBT series strings by high-performance drive units , 2001, IEEE Trans. Ind. Electron..

[7]  J. Yamada,et al.  Low turn-off switching energy 1200 V IGBT module , 2002, Conference Record of the 2002 IEEE Industry Applications Conference. 37th IAS Annual Meeting (Cat. No.02CH37344).

[8]  A. Caiafa,et al.  Characterization and modeling of high-voltage field-stop IGBTs , 2002, Conference Record of the 2002 IEEE Industry Applications Conference. 37th IAS Annual Meeting (Cat. No.02CH37344).

[9]  Y. Ishimura,et al.  Advanced wide cell pitch CSTBTs having light punch-through (LPT) structures , 2002, Proceedings of the 14th International Symposium on Power Semiconductor Devices and Ics.

[10]  H. Husken,et al.  FieldStop IGBT with MOS-like (tailless) turn-off , 2003, ISPSD '03. 2003 IEEE 15th International Symposium on Power Semiconductor Devices and ICs, 2003. Proceedings..

[11]  A. Piazzesi,et al.  Series connection of 3.3 kV IGBTs with active voltage balancing , 2004, 2004 IEEE 35th Annual Power Electronics Specialists Conference (IEEE Cat. No.04CH37551).